Advantech AIMB-221 manual Connecting Peripherals, IDE1

Page 27

You can attach up to one IDE (Integrated Drive Electronics) drive to the AIMB-221's built-in controller.

Wire number 1 on the cable is red or blue and the other wires are gray. Connect one end to connector IDE1 on the motherboard. Make sure that the red/blue wire corre- sponds to pin 1 on the connector (in the upper right hand corner).

Connect the hard drive to the other end of the cable. Wire 1 on the cable should also connect to pin 1 on the hard drive connector, which is labeled on the drive circuit board. Check the documentation that came with the drive for more information.

IDE1

pin.1

#IDE_RST

pin.2

GND

pin.3

IDE_D7

pin.4

IDE_D8

pin.5

IDE_D6

pin.6

IDE_D9

pin.7

IDE_D5

pin.8

IDE_D10

pin.9

IDE_D4

pin.10

IDE_D11

pin.11

IDE_D3

pin.12

IDE_D12

pin.13

IDE_D2

pin.14

IDE_D13

pin.15

IDE_D1

pin.16

IDE_D14

pin.17

IDE_D0

pin.18

IDE_D15

pin.19

GND KEY

 

 

pin.21

IDE_DREQ

pin.22

GND

pin.23

IDE_#DIOW

pin.24

GND

pin.25

IDE_#DIOR

pin.26

GND

pin.27

IDE_IORDY

pin.28

GND

pin.29

IDE_#DACK

pin.30

GND

pin.31

IDE_IRQ

pin.32

NC

pin.33

IDE_DA1

pin.34

IDE_#P66DET

pin.35

IDE_DA0

pin.36

IDE_DA2

pin.37

IDE_#CS1

pin.38

IDE_#CS3

pin.39

IDE_#ACT

pin.40

GND

Chapter 2 Connecting Peripherals

17

AIMB-221 User Manual

Image 27
Contents AIMB-221 Message to the Customer Copyright AcknowledgementsDeclaration of Conformity AIMB-221 Memory Tested for Compatibility Memory CompatibilityProduct warranty Initial Inspection Contents Award Bios Setup Advanced Chipset Features screen Chipset Software Installation Utility VGA Setup71 Chapter Introduction FeaturesSpecifications SystemMemory Input/Output Jumpers and ConnectorsIndustrial features Mechanical and environmental specificationsChapter Board Layout Jumper and Connector LocationsAMD M690E AIMB-221 Block DiagramLabel Function How to set jumpers Safety Precautions Jumper SettingsCmos clear JCMOS1 Watchdog timer output JWDT1ATX/AT mode selector JPSON1 Cache Memory Memory Installation ProceduresProcessor Installation System MemoryID SEL PCI Bus Routing TableMINIPCI1 Routing AD28 / #INTE / #INTF PCI#IDSELAD28 Connecting Peripherals Primary IDE1 IDE Connector IDE1 Connecting PeripheralsPIN DVI2 OptionalConnecting Peripherals Front Panel Connectors JFP1, JFP2, JFP3 JFP1 ATX Soft Power Switch JFP1Reset Connector JFP1 External Speaker JFP2HDD LED Connector JFP2 SM Bus Connector JFP2 PIN6,8JFP2 JFP3 Power LED and keyboard lock connector JFP3JPSON1 ATX/AT Mode Selector JPSON1COM5 Serial Port Header COM 3/4/5/6COM3 COM4CPUFAN1 CPU Fan Connector CPU Fan1System Fan SYSFAN1, SYSFAN2 SYSFAN1SYSFAN2 Parallel Port LPT1 LPT1 JSETCOM1 JSETCOM2 JSETCOM2RS-422 GPIO1 GPIO1HDMI1 VGA1 VGA HdmiLAN1USB12 14 LAN1USB12LAN2USB34 15 LAN2USB34USB56 16 USB56USB78 17 USB78AUDIO1 AudioFPAUD1 FPAUD1SPKOUT1 SPKOUT1Serial ATA Interface SATA1, SATA2, SATA3, SATA4 SATA1 SATA2 SATA3 SATA4 SATA2INV1 22 INV1TVOUT1 23 VGA2 TV-Out OptionalRight click the grey TV icon and select the display mode Lvds LVDS1 JLVDS1 Lvds Power Jumper JLVDS1Page Award Bios Setup Bios Setup program Cmos RAM Auto-backup and Restore Entering SetupIDE channel 0/1 Master/Slave Standard Cmos SetupDate TimeAdvanced Bios Features VideoHalt On First/Second/Third Boot Device CPU FeaturesHard Disk Boot Priority Quick Power On Self TestTypematic Delay msec Boot Up Floppy SeekBoot Up NumLock Status Typematic Rate SettingMemory Hole At 15M-16M Advanced Chipset FeaturesDvmt / Fixed Memory Size Dvmt ModeIntegrated Peripherals On-Chip Frame Buffer SizeSata Mode IDE HDD Block ModeIDE DMA Transfer Access IDE Primary Master/Slave PIO/UDMA Mode AutoAward Bios Setup On board LAN2 ROM Legacy mode supportOn board LAN1 ROM Onboard LAN2 ControlPower Management Setup PowerOn by Modem Suspend ModeHDD Power Down PowerOn by LANPnP/PCI Configurations PC Health Status Spread Spectrum Frequency / Voltage ControlPlease Enter Your Password Password SettingExit Without Saving Save & Exit SetupPage Chipset Software Installation Utility VGA Setup Before you begin Chipset Software Installation Utility and VGA Setup Windows XP Driver Setup Chipset Software Installation Utility and VGA Setup Page Chipset Software Installation Utility and VGA Setup Page Chipset Software Installation Utility and VGA Setup Page LAN Configuration Win XP Driver Setup LAN InstallationLAN Configuration Click Finish to complete the installation AC97 Audio Setup Windows XP Driver Setup AC97 AC97 Audio Setup Page Appendix a Watchdog timer overview Reset/Interrupt selectionProgramming the Watchdog Timer Appendix a Programming the Watchdog Timer Example Programs Table A.1 Watchdog timer registersAppendix a Programming the Watchdog Timer Page Appendix a Programming the Watchdog Timer Page Appendix a Programming the Watchdog Timer