Advantech user manual Initial Inspection, MIC-3043 Illustration

Page 18

Chapter 2 Installation

2.1 Initial Inspection

We have carefully inspected the MIC-3043 mechanically and electrically before shipping. It should be free of marks and scratches and in perfect working order upon receipt. As you unpack the MIC-3043, check it for signs of shipping damage (damaged box, scratches, dents, etc.). If it is damaged or fails to meet specifications, notify our service department or your local representative immediately. Also notify the carrier. Retain the shipping carton and packing material for inspection by the carrier. After inspection, we will make arrangements to repair or replace the unit.

Warning! We strongly recommend that only qualified, experienced personnel install or remove com- ponents. They must exercise extreme caution when doing so.

2.2 The MIC-3043 Illustration

The MIC-3043 is designed for easy installation and maintenance. Figure 2-1 and Figure 2-2 illustrate important components on the front and hot- swappable parts of the enclosure.

Figure 2.1: Front view of MIC-3043

MIC-3043 User Manual

8

Image 18
Contents MIC-3043 Copyright Acknowledgements Product Warranty 1 year Declaration of Conformity FCC Class a CCC Class aTechnical Support and Assistance Document FeedbackPacking List Safety Instructions ING to the Manufacturers Instructions Wichtige SicherheishinweiseSafety Precaution Static Electricity Contents Appendix B Ordering Information Hardware Configuration Introduction Features SpecificationsGeneral Hot-swap Fans Power SupplyDimensions and Weight InputDimensions and Appearance MIC-3043 functional block diagramPage Installation Initial Inspection MIC-3043 IllustrationInstallation Procedures Card Installation and RemovalTo install a card Installing a card into the chassis Installing a 3.5 Hard Disk Drive Before Operating the SystemTo remove a card Connecting the rear I/O module Scsi adaptorHDD number for type B 5IDE adaptor type B Hot-swappable fan maintenance Replacing the Hot-swap FanPage Backplane Specification General InformationSlot Assignments System to peripheral slot signal assignment Connector and Jumper Locations Backplane connector and jumper descriptionConnector and jumper locations on the rear side. MIC-3811 1 AC/DC Power Connector CN3, CN17 Power Switch3 V I/O Voltage Selection Clock Routing Configuration Fan Module ConnectorAlert indicators Pin Assignments MIC-3812 and MIC-3811 System Slot P1 Connector Table A.1 MIC-3812 and MIC-3811 system slot P1 connectorMIC-3812 and MIC-3811 System Slot P2 Connector Table A.2 MIC-3812 and MIC-3811 System Slot P2 ConnectorMIC-3812 and MIC-3811 System Slots P3 Connector Table A.3 MIC-3812 and MIC-3811 System Slot P3 ConnectorMIC-3812 and MIC-3811 System Slots P4 Connector Table A.4 MIC-3812 and MIC-3811 System Slot P4 ConnectorMIC-3812 and MIC-3811 System Slots P5 Connector Table A.5 MIC-3812 and MIC-3811 System Slot P5 ConnectorMIC-3812 and MIC-3811 Peripheral Slot P1 Connector Table A.6 MIC-3812 and MIC-3811 Peripheral Slot P1 ConnectorMIC-3812 and MIC-3811 Peripheral Slot P2 Connector Table A.7 MIC-3812 and MIC-3811 System Slot P2 ConnectorMIC-3812 and MIC-3811 Peripheral Slot P3 Connector MIC-3812 Peripheral Slot P4 Connector Table A.9 MIC-3812 Peripheral System Slot P4 ConnectorMIC-3811 Peripheral Slot P4 Connector Table A.10 MIC-3811 Peripheral System Slot P4 ConnectorMIC-3811 Peripheral Slot P5 Connector Table A.11 MIC-3811 Peripheral Slot P5 ConnectorMIC-3812 Peripheral Slot P5 Connector Table A.12 MIC-3812 Peripheral Slot P5 ConnectorTable A.13 Fan Module Connectors Fan Module ConnectorsLED Board Connector Table A.14 LED Board ConnectorMIC-3812 & MIC-3812 Alarm Board Interface Connector Pin SignalCPCI Power Connector CN1,CN2, and CN5 Table A.16 cPCI Power Connector CN1,CN2, and CN517 AC/DC Power Connector CN3 Table A.17 AC/DC Power Connector CN3Table A.18 AC/DC Power Connector CN17 18 AC/DC Power Connector CN17Enable Power Switch Connector CN15 Table A.19 Enable Power Switch Connector CN15Device Power Connector CN18 Table A.20 Device Power Connector CN18Page Ordering Information Appendix B Ordering Information Default Alarm Module Upgradeable Alarm ModuleTable B.1 Recommended 6U CompactPCI SBC

MIC-3043 specifications

The Advantech MIC-3043 is a cutting-edge embedded computing platform designed for industrial and IoT applications. Hailing from a renowned manufacturer known for its commitment to quality and innovation, the MIC-3043 offers a robust solution tailored for today's demanding environments.

One of the standout features of the MIC-3043 is its compact form factor, enabling seamless integration into various systems without compromising on performance. Despite its small size, it boasts powerful processing capabilities, housing Intel Celeron or Core processors that ensure efficient execution of complex applications. This feature makes it particularly suitable for applications like machine vision, automation, and data acquisition.

The MIC-3043 is engineered with flexible I/O options that cater to diverse industry needs. It supports multiple serial, USB, and Ethernet interfaces, allowing for broad connectivity and easy integration with existing systems. This versatility enables the MIC-3043 to communicate effortlessly with numerous devices, enhancing its usability across different industrial sectors.

In addition to its versatile I/O capabilities, the MIC-3043 prioritizes expandability. It offers mini-PCIe slots that facilitate additional functions through modular expansions, such as wireless communication or additional storage options. This characteristic not only enhances the MIC-3043’s functionality but also positions it as a scalable solution that can evolve with changing technological demands.

The MIC-3043 integrates advanced remote management features, allowing users to monitor system performance and health in real-time. This capability is crucial for reducing downtime and maintenance costs in industrial settings. Coupled with the device's support for various software environments, including Windows and Linux, it provides developers with the flexibility to implement tailored solutions.

Durability is another hallmark of the Advantech MIC-3043. Designed to operate in harsh environments, it complies with industrial standards for temperature and vibration resistance. This resilience ensures reliable operation even in challenging conditions, making it an ideal choice for factory automation, transportation, and energy sectors.

Overall, the Advantech MIC-3043 represents a synthesis of power, flexibility, and durability. Its robust features, combined with a compact design and extensive connectivity options, empower industries to harness the potential of edge computing and IoT, contributing to more efficient and intelligent operations.