Advantech MIC-3043 user manual Installing a card into the chassis

Page 20

2.Make sure that the handles of the card are not latched. Release the handles if they are latched. Handles from different vendors may have different latch designs.

Caution!!! Keep your fingers away from the latch hinges to prevent your fingers from getting pinched.

3.Insert the card into the chassis by sliding the upper and lower edges of the card into the card guides.

4.Push the card into the slot gently by sliding the card along the card guide until the handles meet the rectangular holes of the cross rails.

Figure 2.3: Installing a card into the chassis

Note: If the card is correctly positioned and has been slid all the way into the chassis, the handles should match the rectangular holes. If not, remove the card from the card guide and repeat step 3 again. Do not try to install a card by forcing it into the chassis.

5.Pull the upper handle down and lift the lower handle up to push the card into place.

6.Secure the card by locking the handles into place.

MIC-3043 User Manual

Image 20

Contents MIC-3043 Copyright Acknowledgements Product Warranty 1 year Declaration of Conformity FCC Class a CCC Class aPacking List Technical Support and AssistanceDocument Feedback Safety Instructions ING to the Manufacturers Instructions Wichtige SicherheishinweiseSafety Precaution Static Electricity Contents Appendix B Ordering Information Hardware Configuration Introduction General FeaturesSpecifications Power Supply Dimensions and WeightHot-swap Fans InputDimensions and Appearance MIC-3043 functional block diagramPage Installation Initial Inspection MIC-3043 IllustrationTo install a card Installation ProceduresCard Installation and Removal Installing a card into the chassis To remove a card Installing a 3.5 Hard Disk DriveBefore Operating the System Connecting the rear I/O module Scsi adaptorHDD number for type B 5IDE adaptor type B Hot-swappable fan maintenance Replacing the Hot-swap FanPage Backplane Specification General InformationSlot Assignments System to peripheral slot signal assignment Connector and Jumper Locations Backplane connector and jumper descriptionConnector and jumper locations on the rear side. MIC-3811 3 V I/O Voltage Selection 1 AC/DC Power Connector CN3, CN17Power Switch Alert indicators Clock Routing ConfigurationFan Module Connector Pin Assignments MIC-3812 and MIC-3811 System Slot P1 Connector Table A.1 MIC-3812 and MIC-3811 system slot P1 connectorMIC-3812 and MIC-3811 System Slot P2 Connector Table A.2 MIC-3812 and MIC-3811 System Slot P2 ConnectorMIC-3812 and MIC-3811 System Slots P3 Connector Table A.3 MIC-3812 and MIC-3811 System Slot P3 ConnectorMIC-3812 and MIC-3811 System Slots P4 Connector Table A.4 MIC-3812 and MIC-3811 System Slot P4 ConnectorMIC-3812 and MIC-3811 System Slots P5 Connector Table A.5 MIC-3812 and MIC-3811 System Slot P5 ConnectorMIC-3812 and MIC-3811 Peripheral Slot P1 Connector Table A.6 MIC-3812 and MIC-3811 Peripheral Slot P1 ConnectorMIC-3812 and MIC-3811 Peripheral Slot P2 Connector Table A.7 MIC-3812 and MIC-3811 System Slot P2 ConnectorMIC-3812 and MIC-3811 Peripheral Slot P3 Connector MIC-3812 Peripheral Slot P4 Connector Table A.9 MIC-3812 Peripheral System Slot P4 ConnectorMIC-3811 Peripheral Slot P4 Connector Table A.10 MIC-3811 Peripheral System Slot P4 ConnectorMIC-3811 Peripheral Slot P5 Connector Table A.11 MIC-3811 Peripheral Slot P5 ConnectorMIC-3812 Peripheral Slot P5 Connector Table A.12 MIC-3812 Peripheral Slot P5 ConnectorFan Module Connectors LED Board ConnectorTable A.13 Fan Module Connectors Table A.14 LED Board ConnectorMIC-3812 & MIC-3812 Alarm Board Interface Connector Pin SignalCPCI Power Connector CN1,CN2, and CN5 Table A.16 cPCI Power Connector CN1,CN2, and CN517 AC/DC Power Connector CN3 Table A.17 AC/DC Power Connector CN318 AC/DC Power Connector CN17 Enable Power Switch Connector CN15Table A.18 AC/DC Power Connector CN17 Table A.19 Enable Power Switch Connector CN15Device Power Connector CN18 Table A.20 Device Power Connector CN18Page Ordering Information Appendix B Ordering Information Table B.1 Recommended 6U CompactPCI SBC Default Alarm ModuleUpgradeable Alarm Module

MIC-3043 specifications

The Advantech MIC-3043 is a cutting-edge embedded computing platform designed for industrial and IoT applications. Hailing from a renowned manufacturer known for its commitment to quality and innovation, the MIC-3043 offers a robust solution tailored for today's demanding environments.

One of the standout features of the MIC-3043 is its compact form factor, enabling seamless integration into various systems without compromising on performance. Despite its small size, it boasts powerful processing capabilities, housing Intel Celeron or Core processors that ensure efficient execution of complex applications. This feature makes it particularly suitable for applications like machine vision, automation, and data acquisition.

The MIC-3043 is engineered with flexible I/O options that cater to diverse industry needs. It supports multiple serial, USB, and Ethernet interfaces, allowing for broad connectivity and easy integration with existing systems. This versatility enables the MIC-3043 to communicate effortlessly with numerous devices, enhancing its usability across different industrial sectors.

In addition to its versatile I/O capabilities, the MIC-3043 prioritizes expandability. It offers mini-PCIe slots that facilitate additional functions through modular expansions, such as wireless communication or additional storage options. This characteristic not only enhances the MIC-3043’s functionality but also positions it as a scalable solution that can evolve with changing technological demands.

The MIC-3043 integrates advanced remote management features, allowing users to monitor system performance and health in real-time. This capability is crucial for reducing downtime and maintenance costs in industrial settings. Coupled with the device's support for various software environments, including Windows and Linux, it provides developers with the flexibility to implement tailored solutions.

Durability is another hallmark of the Advantech MIC-3043. Designed to operate in harsh environments, it complies with industrial standards for temperature and vibration resistance. This resilience ensures reliable operation even in challenging conditions, making it an ideal choice for factory automation, transportation, and energy sectors.

Overall, the Advantech MIC-3043 represents a synthesis of power, flexibility, and durability. Its robust features, combined with a compact design and extensive connectivity options, empower industries to harness the potential of edge computing and IoT, contributing to more efficient and intelligent operations.