3Com C17302, 3C17300, C17304 manual Setting Up the Switch with IP Information

Page 40

40CHAPTER 3: SETTING UP FOR MANAGEMENT

2Open your terminal emulation software and configure the COM port settings to which you have connected the cable. The settings should be set to match the default settings for the Switch, which are:

■19,200 baud

■8 data bits

■no parity

■1 stop bit

■no hardware flow control

Refer to the documentation that accompanies the terminal emulation software for more information.

Setting Up the Switch with IP Information

You are now ready to manually set up the Switch with IP information using the command line interface.

1The command line interface login sequence begins as soon as the Switch detects a connection to its console port.

If the login prompt does not begin immediately, press Return a few times until it starts.

2At the login and password prompts, enter admin as your user name and press Return at the password prompt. If you have logged on correctly, the top-level menu of the command line interface is displayed as shown in the example in Figure 12.

Page 39 Page 41
Image 40
Page 39 Page 41
Contents SuperStack 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Setting UP for Management PIN-OUTS Index Regulatory Notices About this Guide Icon Description ConventionsConvention Description Related DocumentationProduct Introducing About the Switch SeriesSwitch 4200 Series Front View DetailIntroducing the Superstack 3 Switch 4200 Series Fiber GBICs 1000BaseT GBICsColor Indicates Port Status LEDs 10BASE-T/100BASE-TX ports Port Status LEDs Gbic portsPower/Self Test LED Color IndicatesUnit LEDs Alert LEDSystem RPS. See Connecting a Redundant Power System on Rear View DetailFeature Switch 4200 Series Automatic IP Configuration Duplex ModeRmon Alarm Quality of Service QoSInstalling the Switch Choosing a Suitable Package ContentsSite Rack-mounting Repeat steps 2 and 3 for the other side of the Switch Fitting a bracket for rack-mountingStacking Units Unit line up with the recesses of the lower unitOn the unit above. Cable lengths of between 14 cm 5.5 100 m 328 ft can be used for stackingPower-up Powering-upSwitch 4200 Series SequencePower/Self Test LED colors Color StateFiber cables Cross-over Cable Straight-through CableApproved Gbic The 3Com approved Gbic transceivers are Gbic OperationTransceivers Installing the Switch Gbic Installing the Switch Setting UP for Management Setting Up Configure IP information manually for your Switch or viewAutomatically configured IP information OverviewManual IP Configuration Automatic IP ConfigurationSetting UP for Management Manually Configuring IP Information Pre-requisitesConfiguring the Workstation with IP Information Connecting the Workstation to the SwitchSetting Up the Switch with IP Information Using Command Line Interface via Telnet Example top-level command line interface menu Connecting a workstation to the Switch via the console port Setting Up the Switch with IP Information Example top-level command line interface menu Viewing Configured IPAutomatically Viewing Automatically Configured IP Information Viewing IP Information via the Console Port Methods of Managing a Switch Refer to Setting Up Command Line Interface Management on Command Line Network Using TelnetInterface Management CLI Management viaInterface Setting Up WebChoosing a Browser Setting Up Snmp Management Protocol Snmp can manage a Switch ifOver the Network Management workstationDefault Users User Default Name Password Access LevelSecurity Device User Modify operation on the web interface Setting UP for Management Problem Solving For Technical Support information, see Appendix DSolving Problems Solutions belowPower LED does not light On powering-up, the Power/Self Test LED lights yellowProblems Solving Communication ProblemsSolving Hardware Snmp fan fail trap hardware failure IP AddressingFormation Solving StackHow do you obtain a registered IP Address? Solving Software Upgrade Problems Problem Solving Safety Information Important Safety Information This must be approved for the country where it is usedImportant Safety Information ’information de Sécurité Importante ’information de Sécurité Importante Wichtige Sicherheitsinformationen Vorsicht Europe Appendix a Safety Information Null Modem Cable PC-AT Serial CablePin to RS-232 25-pin Pin to 9-pinConnectors Pin Number Signal FunctionModem Cable RJ-45 Pin1000BASE-T RJ-45 RJ-45 connectorsPin Assignments Pin assignments Switch 4226T 3C17300 Standards Supported Protocols Used for AdministrationTerminal Emulation Switch 4250T 3C17302 SnmpSwitch 4228G 3C17304 Services Online TechnicalUsername anonymous Asia, Pacific Rim From this region, e-mailEurope, Middle East and Africa From this region, enter the URLAsia, Pacific Rim Europe, Middle East, and AfricaCountry Telephone Number Asia, Pacific Rim Country Telephone Number Latin America Index Snmp Regulatory Notices
Related manuals
Manual 79 pages 26.18 Kb

C17304, C17302, 3C17300 specifications

The 3Com C17304, 3C17300, and C17302 are notable models in the 3Com networking product line, renowned for their performance and technological advancements. These models cater to various networking environments, providing robust solutions for both small and medium-sized businesses as well as larger enterprises seeking reliable connectivity.

The 3Com C17304 is recognized for its formidable capacity and flexibility. It offers a high port density, which allows for multiple devices to connect without compromising performance. This model features built-in support for Power over Ethernet (PoE), enabling the powering of devices such as IP cameras and phones directly through the network cable. The 3Com C17304 is designed with advanced security features, including integrated VLAN support for traffic segmentation and enhanced security protocols to protect sensitive data.

The 3C17300 is another essential player in this lineup, embodying versatility and ease of use. This model is equipped with a user-friendly interface that simplifies network management, making it accessible for IT professionals at all levels. The 3C17300 includes capabilities for Layer 2 switching, providing efficient data forwarding with minimal latency. Its intelligent features, such as link aggregation and QoS (Quality of Service), ensure optimized bandwidth utilization while prioritizing critical applications.

Meanwhile, the C17302 is specifically engineered for performance-driven environments. It excels in delivering high-speed connectivity with its support for Gigabit Ethernet, significantly enhancing data transfer rates. The C17302 also incorporates advanced routing capabilities, allowing for dynamic network management and improved performance in complex network topologies. Furthermore, this model boasts reliability with redundancy features designed to minimize downtime, ensuring consistent access to network resources.

All three models leverage innovative technologies to deliver superior performance. They support various standards such as IEEE 802.1Q for VLAN tagging and IEEE 802.3ad for link aggregation. User-centric features like SNMP for network monitoring and troubleshooting enhance the overall management experience. These switches are built to provide scalability, enabling businesses to expand their networks seamlessly as demands grow.

In summary, the 3Com C17304, 3C17300, and C17302 showcase advanced features, reliability, and effective performance, making them integral components of modern networking solutions. Ideal for a range of applications, they help businesses optimize their network infrastructure while maintaining robust security and efficient data handling.
Top Page Image Contents