3Com manual Configuring the Corebuilder 7000 Family ATM Switch

Page 66

66CHAPTER 6: CONFIGURING THE COREBUILDER 7000 FAMILY ATM SWITCH

3The LMA automatically prompts you to enter ATM addresses for the ports that you have specified as IISP. These are ATM addresses of network devices that you want the IISP port to recognize for routing purposes. They are placed in the routing table of the port. You need to enter these addresses manually because the IISP protocol does not automatically recognize them. You can enter more than one address; press Enter to end the sequence of addresses.

***The following are addresses of ports you have defined as IISP. You may enter more than one address per port.

When you have finished press <Enter>:

ATM address for port <5.2> (19 bytes-When less: end with '.*'): 47.00.00.00.00.00.3e.00.00.b0.00.c0.da.69.00.c0.da.11.22

ATM address was set for port <5.2>

ATM address for port <5.2> (19 bytes-When less: end with '.*'): 47.00.00.00.00.00.3e.00.00.b0.00.00.00.00.c0.da.11.22.00

ATM address was set for port <5.2>

ATM address for port <5.2> (19 bytes-When less: end with '.*'):

4The LMA automatically prompts you for the NNI type of the ports that you have specified as IISP. Specify the NNI type as User or Network.

***The following is a profile of ports you have defined as Gateway: Profile of port <5.2> (U<ser>, N<etwork>): N

5Repeat until you have specified all the IISP ports.

LE Client Configuration Section This section prompts you for the LAN Emulation Client configuration. You give names to the ELANs that you want to be active in the network. In the Virtual Network Configuration section, you will assign Ethernet ports to the ELANs you have named in this section to create VLANs. Until then, the ELANs are considered potential ELANs.

You can enter the names of resident ELANs of the switch you are setting up and you can enter names of ELANs from other devices in the network. You can define any number of potential ELANs. To end the sequence, press Enter.

The names of the ELANs resident on a particular switch all have the form elanXXXX_n where “XXXX” is a number unique to the switch and “n” is

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Software Version 4.55 Base and Extended 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Installing and Connecting Corebuilder Modules Configuring the Corebuilder 7000 Family ATM Switch Troubleshooting Glossary 3COM Corporation Limited Warranty Page Information About this GuideFinding Specific This GuideConventions Icon DescriptionConvention Description CoreBuilder Family ATM Switch Documents DocumentationCoreBuilder 7000 Family ATM Switches Operations Guide Document 3Com Part NumberMap If you want to ReadComments YearCompliance Overview Overview Component SummaryInstallation Stage Chapter Interface ModuleFans Stage Chapter Overview Unpacking Family ATM SwitchUnpacking Instructions CoreBuilderUnpacking Instructions Family ATM Switch Safety PrecautionsVorsichtsmaßnahm en Mesures de sécuritéTable Top InstallationPreparation As shippedPreparation For installation Universal Mounting Hole Pattern Family ATM Switch Core Builder Modules Power Supply Installing a Power To install a power supply module Supply ModuleSwitch Module Module to ensure operation should the main switch moduleModule, see in the Operations Guide Module Setting up Switch Module Redundancy Redundancy You should see the following displayGeneral Description of the Procedure Preparatory StepsProcedure Execution Hardware Redundancy Setup NMS-Based Lane Redundancy SetupVerifying Lane Redundancy Setup Lecs Elan database does not transfer automaticallyInstalling and Connecting Corebuilder Modules Port Interface Module ATM Interface Daughter CardsShows the E-3 daughter card Port ATM Interface Module Fan Tray Connecting toSwitch to different types of network devices Network DevicesFiber Optic Power Budget of 3Com Products OC-3 SMCoreBuilder SM-1300 SDX-1155B ATM port MM-820 15.1 Selecting a Power Cord Plugging in the Unit POWER-ON System StatesHow they are indicated on the LED display I L Color Description SourcePort Interface Module LEDsList the permanent 4-port interface module panel LEDs Link Status Color Description LOSPOWER-ON Logging in to Configuring Corebuilder 7000 Family ATM SwitchLogin screen appears Topics covered in this chapter includeSetup Integrated FastChassis-oriented Setup Chassis-wide VLANsFull Setup Mode Switch Setup ModeSetup Mode Selection Setting Special Parameters Setup Section DescriptionSections Default Parameter Values Following message appears on the screenType To Go Pnni is available in version 4.5 extended only Pnni Parameters Enter Pnni Node Level 0 to 104 Factory default is Your choice is displayedAs in , select the capacity of Bank Configuring the Corebuilder 7000 Family ATM Switch Pnni is available in version 4.5 extended only Configuring the Corebuilder 7000 Family ATM Switch Integrated Fast Setup Configuring the Corebuilder 7000 Family ATM Switch Following shows a typical virtual network configuration Type To performEthernet port Belongs To VN # 1-17 Integrated Fast Setup Integrated Fast Setup configures a minimum set of network Additional SwitchConfiguration Some additional configuration tasks might beConfiguring a PVC Configuring SVCsConfiguring Network Prefix and ATM Addresses Configuring Clock SynchronizationMenu Option Path Description VPI/VCIStoring RetrievingParameters Configuring the Corebuilder 7000 Family ATM Switch SYS\ 3 LOA \6 TCU Following messages are displayed for each data type Loading a Single Configuration Data TypeEnter the name of the file to receive the data on disk Upload status is displayed as followsFor loading a single item you can enter a full file name Loading the Other Data TypeConfirm the download Download status is displayed as follows Utility Batch file nameFollowing methods System is now in operational mode Method 1 Shift OMethod 2 dbgoff.bat Migrating from E-IISP to Pnni Redundancy Corebuilder 7000 Family ATM Switch Redundant Power SupplyTypes of Power Supplies CoreBuilder 7000 family power supplies are shown in Table Load SharingOverloading Port and 8-port ATM Interface Cards ATM Physical ModulesCoreBuilder 720X Ethernet/ATM Interface Card CoreBuilder 74XX Ethernet/ATM Interface Card CoreBuilder 76XX Fast Ethernet Interface CardData Closet Ethernet ATM Data Center with high-density Fast EthernetProviding Redundancy for Various Power Loads Other applicationsPower Supply 90A AC Power Supply Specifications 40A DC Power SupplyParameter Channel Heat Dissipation W Heat Dissipation BTU Troubleshooting Problem Recommended ActionFamily ATM switch power supply Power SupplyTroubleshooting Problem Possible Cause Recommended ActionSafety Precautions for Fiber Optics Connectors Procedure ActionTroubleshooting Switching Module Specifications Standards supported Power SupplyCoreBuilder Management and Interface LEDs Switch Module Interface CardCoreBuilder Management and Interface Connectors InterfacesPage Safety Information Bodily HarmDommages KörperlicheSchäden CorporelsSchäden am Gerät Appendix B Safety Information Site Requirements RequirementsRecommendations Wiring ClosetThermal ConsiderationsLocation codes or some type of floor grid matrix Ambient temperature and humidityDistribution Rack Distribution rack refer to FigureAppendix C Site Requirements Installing New Cabling If you are installing new cabling, follow these guidelinesCabling Requirements Accordingly ATM CablingJumper location, and any additional information Used at the siteFiber optic cable Dirt on the Fiber Optic LensDamaged Transceiver Due to Excessive Insertion Force Comparing Fiber to Specifications Specification DescriptionNumerical Aperture Example Type of Insertion LossMHz km / xkm = y MHz MHz km / 2 km = 250 MHzCategory Specifications Descriptions Single Mode Fiber Specifications Category Output power Mixed Fibers combination CoreBuilder 7000 Serial Port Serial Port PinoutsPin Signal Meaning Pin Male Pin FemaleCoreBuilder 7000 Serial Port To Modem Port Pin Male Appendix D Cabling Requirements Technical Support ServicesServices Online TechnicalHours a day, 7 days a week Access by Analog ModemUsername anonymous Country Data Rate Telephone NumberAccess by Digital Modem 847 262408 727 Europe, South Africa, and Middle East Country Telephone Number Asia, Pacific RimCountry Telephone Number Fax Number Appendix E Technical Support Glossary Glossary Glossary Communications Glossary Glossary Glossary OAM Channel Glossary Glossary Glossary Index PVC Hardware kit LES Fast 56 setup mode full UNI Setup 39 virtual LAN Index 3Com Corporation Limited Warranty Warranties Exclusive
Related manuals
Manual 66 pages 7.48 Kb

7000 specifications

The 3Com 7000 is a robust and versatile networking solution designed to meet the demands of enterprise environments. Renowned for its reliability and scalability, the 3Com 7000 is highly suitable for organizations requiring efficient data handling and enhanced network performance. This multi-layer switching platform integrates advanced technologies, making it a preferred choice for modern businesses.

One of the standout features of the 3Com 7000 is its modular architecture. This design allows businesses to customize their network according to specific requirements by adding or replacing various modules. The modularity ensures that organizations can scale their network operations without significant downtime or the necessity of overhauling existing infrastructure. Such flexibility is vital for growing enterprises that need to adapt to variable workloads.

The 3Com 7000 also incorporates advanced Layer 3 routing capabilities. This feature enhances the efficiency of data transmission and bolsters the overall responsiveness of the network. By allowing routing functions to occur directly on the switch, it reduces latency and optimizes traffic flow, which is critical for applications requiring high availability, such as VoIP and video conferencing.

Security is another core characteristic of the 3Com 7000. It comes equipped with built-in security protocols and features such as Access Control Lists (ACLs) and VLAN support, which segregate network resources and protect sensitive data. These security measures ensure that only authorized devices can access specific segments of the network, thus fortifying the organization's information security posture.

In terms of management, the 3Com 7000 offers an intuitive interface for monitoring and controlling network operations. It supports various management protocols and software, which facilitate streamlined administration and configuration. This ease of management can significantly reduce the operational burden on IT staff, allowing them to focus on strategic initiatives.

Additionally, the 3Com 7000 is designed for high performance. It supports extensive bandwidth and low-latency communications, making it ideal for high-demand applications. The ability to handle multiple simultaneous connections without compromising speed makes it an excellent choice for enterprises that rely on real-time data processing.

In summary, the 3Com 7000 is a sophisticated networking solution characterized by its modularity, advanced routing capabilities, robust security features, user-friendly management, and high performance. These attributes make it a compelling choice for enterprises looking to enhance their networking infrastructure for a competitive edge.
Top Page Image Contents