3Com 4510G manual CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCdone

Page 56

Step2 Select Transfer > Send File in the HyperTerminal’s window. Click Browse in the pop-up dialog box (as shown in Figure 5-5) to select the application file to be downloaded (for example, bootrom.btm), and select Xmodem from the Protocol drop-down list.

Figure 5-5Send file dialog box

Step3 Click Send. The following dialog box appears:

Figure 5-6Page for file sending

After the Boot ROM file is downloaded, the terminal displays the following information:

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCdone!

Bootrom updating

done!

Your baudrate should be set to 19200 bps again!

Press enter key when ready

You do not need to reset the HyperTerminal’s baud rate and can skip the last step if you have chosen 19200 bps. In this case, the system returns to the Boot ROM update menu directly instead of displaying the prompt "Your baudrate should be set to 19200 bps again! Press enter key when ready".

5-7

Page 55 Page 57
Image 56
Page 55 Page 57
Contents 3Com Switch 4510G Family Environmental Statement Chapter Contents About This ManualOrganization ConventionsRelated Documentation Obtaining DocumentationCreate Folder Convention DescriptionTable of Contents Page Switch 4510G 24-Port Switch 4510G 48-Port OverviewIntroduction to Switch 4510G Switch 4510G 24-PortSwitch 4510G 48-Port Specification PortsConsole Port 10/100/1000Base-T Ethernet PortModel SFP port 10/100/1000Base-T Ethernet port SFP PortCombo Port LEDs System Status LEDRPS Status LED LEDsPort Mode LED Seven-Segment LEDMark Status Description System status Seven-segment LED DescriptionStatus System status Seven-segment LED Description Status Description Port mode Ethernet port status10/100/1000Base-T Auto-Sensing Ethernet Port Status LED Interface Module Status LED Optional Interface ModulesSFP Port Status LED CX4 Cable Connector type Length Short-haul Dual-Port 10 GE CX4 Interface ModuleDistance Central Max Transceiver Connector Fiber TransmissionDual-Port 10 GE XFP Interface Module One-port 10 GE XFP Interface Module Dual-Port 10 GE SFP+ Interface ModuleConnector Fiber Transmission Cable type Distance Transceiver Central MaxDescription of LEDs of Interface Modules Safety Precautions Installation SiteTemperature/Humidity CleannessElectromagnetic Susceptibility Gas Maximum concentration mg/mInstallation Tools Laser SafetyInstalling the Switch Installation Flow of the SwitchUse Front Mounting Brackets to Install a Switch Introduction to Mounting BracketUse Front Mounting Brackets and a Tray to Install a Switch When a Grounding Strip is Available Mounting the Switch on a WorkbenchConnecting the Grounding Cable Page Where a Grounding Conductor Can be Buried Other Installation SitesSwitch module Power supply mode Connection method Connecting the Power CordsConnecting the AC Power Cord 9Connect an AC power cord to a horizontal AC power socket Installing an Interface Module Connecting the RPS Power CordInstalling an Interface Card Removing an Interface ModuleInstalling Dedicated CX4/SFP+ Cable Removing Dedicated CX4/SFP+ CableTask Remarks Installing Switches for an IRFInstallation Flow for an IRF Drawing a Plan for an IRF with Switches For details, see Installing an Interface ModuleSelect the proper interface modules and cables Page Verifying the Installation 22Cable connections for an IRF with 1-port interface modulesSetting up the Configuration Environment Connecting the Console CableRJ-45 Signal Direction DB-9 Console CableSetting Terminal Parameters Connection Procedure4Set the serial port used by the HyperTerminal connection 6HyperTerminal window Powering on the Switch Booting the SwitchChecking before Powering on the Switch Describes the fields above 2Description on the fields Changing the Startup Mode Enter Y. The system displays the following information BUS Clock Speed 33MHz Memory Size 128MB Mac Address Page Introduction to Loading Modes Loading Software Through the Boot ROM MenuBoot Menu Press Ctrl + B. The system displays Loading Software Using Xmodem Through Console Port Introduction to XmodemRequired ROM file effective2Properties dialog box Cccccccccccccccccc CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCdone Loading Software Using Tftp through Ethernet Port Loading host softwareLoad File name Loading Software Using FTP Through Ethernet Port Introduction to FTPDescription Loading Software Using FTP Loading Software Through CLILoading Software Using Tftp Update the Boot ROM program on the switchPassword Missing Failure Missing User PasswordMissing Boot ROM Password Software Loading FailurePower Supply Failure AC inputRPS input RPS&AC inputSteady red Fan FailureMark State System status LED Troubleshooting when the terminal display is illegible Configuration System FailureTroubleshooting when there is no terminal display

4510G specifications

The 3Com 4510G is a high-performance, stackable switch designed to meet the demands of modern enterprise networks. This switch is part of the 3Com switch family, known for its reliability, ease of use, and advanced features tailored for both small and medium-sized businesses, as well as larger enterprises.

One of the standout features of the 3Com 4510G is its high-density 10/100/1000 Mbps Gigabit Ethernet ports. With a configuration of up to 48 ports, this switch allows for efficient data transfer and connectivity among devices in the network. The switch also supports Power over Ethernet (PoE), enabling it to deliver power to PoE-enabled devices like IP phones, wireless access points, and security cameras, simplifying deployment and reducing cable clutter.

In terms of performance, the 3Com 4510G offers non-blocking architecture, which ensures that any port can handle its maximum throughput without causing bottlenecks. This switch is equipped with a high-performance switching capacity, allowing for seamless data flow and minimizing latency, which is critical for applications such as voice over IP (VoIP) and video conferencing.

The 3Com 4510G also provides advanced Layer 2 and Layer 3 routing capabilities. It supports features like VLANs, link aggregation, and multicast routing, which enhance network segmentation and optimize traffic management. The switch supports a comprehensive set of security features, including Access Control Lists (ACLs) and port security, to safeguard the network against unauthorized access.

Management is another strong suite of the 3Com 4510G. It supports Simple Network Management Protocol (SNMP) for effective network monitoring and management, as well as a user-friendly web interface and command-line interface (CLI) for easy configuration. Network administrators can easily troubleshoot and maintain the switch through these interfaces, ensuring optimal performance.

Additionally, the 3Com 4510G is designed with energy efficiency in mind, adhering to environmental standards, and thereby reducing operational costs over time.

With its robust feature set, advanced technologies, and high reliability, the 3Com 4510G switch stands out as an excellent choice for organizations looking to build a scalable and efficient network infrastructure. Its combination of performance, ease of management, and security makes it a valuable asset for meeting current and future networking needs.
Top Page Image Contents