3Com 4510G manual Optional Interface Modules, SFP Port Status LED, Interface Module Status LED

Page 15

SFP Port Status LED

The port mode LED and the SFP port status LED together indicate the SFP port operation status. Refer to Table 1-11 for details.

Table 1-11SFP port status LEDs description

 

Status

 

 

 

 

 

 

 

 

 

Description

 

Port mode

 

 

Ethernet port

 

 

 

 

 

 

 

 

LED

 

 

status LED

 

 

 

 

 

 

 

Steady green

 

The port operates at a rate of 1000 Mbps; the LED is fast

 

 

 

 

 

flashing when data is being sent and/or received on the port.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Steady green

 

Steady yellow

 

The port operates at a rate of 100 Mbps; the LED is fast

 

 

 

flashing when data is being sent and/or received on the port.

 

 

 

 

 

 

(rate mode)

 

 

 

 

 

 

 

Flashing yellow

 

POST failed on the port.

 

 

 

 

 

 

 

 

 

(3 Hz)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Off

 

The port is not up.

 

 

 

 

 

 

 

 

 

 

 

 

Steady green

 

The port operates in full-duplex mode; the LED is fast flashing

 

 

 

 

 

when data is being sent and/or received on the port.

 

 

 

 

 

 

 

 

Steady yellow

 

 

 

 

 

 

 

Flashing yellow

 

 

 

(duplex mode)

 

 

POST failed on the port.

 

 

(3 Hz)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Off

 

The port is not up.

 

 

 

 

 

 

 

 

Interface Module Status LED

Table 1-12Interface module status LED description

 

Mark

Status

Description

 

 

Green

The interface module is in the slot and operates normally.

 

MOD1

 

 

 

Flashing yellow

The inserted interface module type is incorrect or the interface

 

MOD2

module fails.

 

 

 

 

Off

No interface module is installed.

 

 

 

 

Optional Interface Modules

The Switch 4510G provide two interface module slots on the rear panel. You can select the interface modules in Table 1-13 as needed.

The Switch 4510G support IRF, requiring physical connections between devices. The 10 GE ports of the supported interface modules support IRF, allowing you to connect the switches through these 10 GE ports for IRF implementation.

Table 1-13Description of the supported interface modules

 

Model

 

 

Description

 

Interface quantity

 

Remarks

 

 

 

 

 

and type

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Short-haulDual-Port

2 × 10 Gbps electrical

 

Suitable for short-distance

 

3C17767

 

10 GE CX4 Interface

 

connections using CX4 power

 

 

ports

 

 

 

 

 

Module

 

cables, and support IRF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1-9

 

 

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 3Com Switch 4510G Family Environmental Statement Conventions Chapter ContentsAbout This Manual OrganizationConvention Description Related DocumentationObtaining Documentation Create FolderTable of Contents Page Overview Switch 4510G 24-Port Switch 4510G 48-PortSwitch 4510G 24-Port Introduction to Switch 4510GSwitch 4510G 48-Port 10/100/1000Base-T Ethernet Port SpecificationPorts Console PortSFP Port Combo PortModel SFP port 10/100/1000Base-T Ethernet port LEDs LEDsSystem Status LED RPS Status LEDSystem status Seven-segment LED Description Port Mode LEDSeven-Segment LED Mark Status DescriptionStatus Description Port mode Ethernet port status 10/100/1000Base-T Auto-Sensing Ethernet Port Status LEDStatus System status Seven-segment LED Description Optional Interface Modules SFP Port Status LEDInterface Module Status LED Short-haul Dual-Port 10 GE CX4 Interface Module CX4 Cable Connector type LengthCentral Max Transceiver Connector Fiber Transmission Dual-Port 10 GE XFP Interface ModuleDistance Dual-Port 10 GE SFP+ Interface Module One-port 10 GE XFP Interface ModuleTransceiver Central Max Connector Fiber Transmission Cable type DistanceDescription of LEDs of Interface Modules Installation Site Safety PrecautionsGas Maximum concentration mg/m Temperature/HumidityCleanness Electromagnetic SusceptibilityLaser Safety Installation ToolsInstallation Flow of the Switch Installing the SwitchIntroduction to Mounting Bracket Use Front Mounting Brackets to Install a SwitchUse Front Mounting Brackets and a Tray to Install a Switch Mounting the Switch on a Workbench Connecting the Grounding CableWhen a Grounding Strip is Available Page Other Installation Sites Where a Grounding Conductor Can be BuriedConnecting the Power Cords Connecting the AC Power CordSwitch module Power supply mode Connection method 9Connect an AC power cord to a horizontal AC power socket Connecting the RPS Power Cord Installing an Interface ModuleRemoving an Interface Module Installing an Interface CardRemoving Dedicated CX4/SFP+ Cable Installing Dedicated CX4/SFP+ CableInstalling Switches for an IRF Installation Flow for an IRFTask Remarks For details, see Installing an Interface Module Drawing a Plan for an IRF with SwitchesSelect the proper interface modules and cables Page 22Cable connections for an IRF with 1-port interface modules Verifying the InstallationConsole Cable Setting up the Configuration EnvironmentConnecting the Console Cable RJ-45 Signal Direction DB-9Connection Procedure Setting Terminal Parameters4Set the serial port used by the HyperTerminal connection 6HyperTerminal window Booting the Switch Checking before Powering on the SwitchPowering on the Switch Describes the fields above 2Description on the fields Changing the Startup Mode Enter Y. The system displays the following information BUS Clock Speed 33MHz Memory Size 128MB Mac Address Page Loading Software Through the Boot ROM Menu Boot MenuIntroduction to Loading Modes Press Ctrl + B. The system displays Introduction to Xmodem Loading Software Using Xmodem Through Console PortROM file effective Required2Properties dialog box Cccccccccccccccccc CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCdone Loading host software Loading Software Using Tftp through Ethernet PortLoad File name Introduction to FTP Loading Software Using FTP Through Ethernet PortDescription Loading Software Through CLI Loading Software Using FTPUpdate the Boot ROM program on the switch Loading Software Using TftpSoftware Loading Failure Password Missing FailureMissing User Password Missing Boot ROM PasswordRPS&AC input Power Supply FailureAC input RPS inputFan Failure Mark State System status LEDSteady red Configuration System Failure Troubleshooting when there is no terminal displayTroubleshooting when the terminal display is illegible

4510G specifications

The 3Com 4510G is a high-performance, stackable switch designed to meet the demands of modern enterprise networks. This switch is part of the 3Com switch family, known for its reliability, ease of use, and advanced features tailored for both small and medium-sized businesses, as well as larger enterprises.

One of the standout features of the 3Com 4510G is its high-density 10/100/1000 Mbps Gigabit Ethernet ports. With a configuration of up to 48 ports, this switch allows for efficient data transfer and connectivity among devices in the network. The switch also supports Power over Ethernet (PoE), enabling it to deliver power to PoE-enabled devices like IP phones, wireless access points, and security cameras, simplifying deployment and reducing cable clutter.

In terms of performance, the 3Com 4510G offers non-blocking architecture, which ensures that any port can handle its maximum throughput without causing bottlenecks. This switch is equipped with a high-performance switching capacity, allowing for seamless data flow and minimizing latency, which is critical for applications such as voice over IP (VoIP) and video conferencing.

The 3Com 4510G also provides advanced Layer 2 and Layer 3 routing capabilities. It supports features like VLANs, link aggregation, and multicast routing, which enhance network segmentation and optimize traffic management. The switch supports a comprehensive set of security features, including Access Control Lists (ACLs) and port security, to safeguard the network against unauthorized access.

Management is another strong suite of the 3Com 4510G. It supports Simple Network Management Protocol (SNMP) for effective network monitoring and management, as well as a user-friendly web interface and command-line interface (CLI) for easy configuration. Network administrators can easily troubleshoot and maintain the switch through these interfaces, ensuring optimal performance.

Additionally, the 3Com 4510G is designed with energy efficiency in mind, adhering to environmental standards, and thereby reducing operational costs over time.

With its robust feature set, advanced technologies, and high reliability, the 3Com 4510G switch stands out as an excellent choice for organizations looking to build a scalable and efficient network infrastructure. Its combination of performance, ease of management, and security makes it a valuable asset for meeting current and future networking needs.
Top Page Image Contents