3Com 09-0487-002 manual Replacing the Fuse, Opening the Fuse-holder in the AC Receptacle Assembly

Page 7

LinkBuilder FDDI Workgroup Hub User Guide Release Note 7

Replacing the Fuse

If the hub’s LEDs are no longer lit, the unit may be disconnected from its AC power cord. If the power cord is securely connected but the LEDs are still not lit, the fuse probably needs to be replaced.

The fuse is located in the hub’s AC receptacle assembly and supplied as standard equipment for the hub. It is a “quick-acting,” FSF034.1523 fuse or equivalent, rated at 5 amps, 250 volts.

To replace the fuse, follow these steps:

1.Locate the AC receptacle on the hub’s back panel.

2.Disconnect the AC power cord.

3.Carefully pry open and pull out the fuse-holder, as shown in Figure 1.

 

 

 

 

250

V

fuse

 

 

 

with

 

 

only

 

 

Use

 

 

avec

 

 

 

 

 

 

 

 

 

 

 

uniquementV

Employer

 

250

 

 

 

un

fusible

 

 

 

 

 

 

 

 

 

Figure 1. Opening the Fuse-holder in the AC Receptacle Assembly

Image 7
Contents Change in FCC Compliance Contents of the LinkBuilder Diskette2-14 Removing Modules 2-14 Check the Baud Rate Setting After PostCorrections in the User Guide Software-Related CorrectionsPress the Reset button once, or enter the reset command 5-21 Fault Log Display 5-20 route dump and route add Commands1-7 Media Flexibility A-7 Management Module Failure Error CodeC-22 show rev Command Hardware-Related Corrections2-22 Note 2-21 Unshielded Twisted-Pair CableReplacing the Fuse Opening the Fuse-holder in the AC Receptacle AssemblyRemoving the Fuse

09-0487-002 specifications

The 3Com 09-0487-002 is a robust network interface card (NIC) designed to meet the demands of modern networking environments. Known for its reliability and performance, this card is particularly suited for businesses looking to enhance their networking capabilities.

One of the main features of the 3Com 09-0487-002 is its compatibility with various operating systems, which ensures that it can be seamlessly integrated into diverse IT infrastructures. This flexibility enables businesses to upgrade their existing systems without the need for extensive changes to their hardware setup.

The NIC supports both wired and wireless connectivity options, providing users with the versatility to adapt to different network environments. This adaptability makes the 3Com 09-0487-002 an ideal choice for organizations that require both stable wired connections and the freedom of wireless networking.

In terms of performance, this NIC boasts impressive data transfer speeds, typically reaching up to 1 Gbps. This allows for quick and efficient data exchange within networks, making it suitable for high-bandwidth applications, such as video streaming and large file transfers. Additionally, the card incorporates advanced technologies such as full-duplex Ethernet, which allows simultaneous sending and receiving of data packets, further enhancing its efficiency.

Security is another critical characteristic of the 3Com 09-0487-002. The card features support for various encryption protocols, ensuring secure data transmission and protecting sensitive information from potential cyber threats. This is particularly vital for businesses that handle confidential data and need to comply with regulatory requirements.

Another noteworthy aspect of the 3Com 09-0487-002 is its ease of installation and user-friendly interface. IT teams can quickly deploy the card with minimal technical expertise, reducing downtime and allowing businesses to enhance their networking capabilities without extensive training.

Lastly, reliability is a hallmark of the 3Com brand, and the 09-0487-002 is no exception. It is built to withstand the rigors of continuous operation, making it a dependable choice for critical business applications. Overall, the 3Com 09-0487-002 network interface card stands out as a feature-rich solution that combines performance, security, and ease of use, making it an excellent addition for any organization looking to bolster its network infrastructure.