Rosewill RNX-N250UBE user manual 2400.0-2483.5 MHz, Country, Restriction, Reason/remark

Page 2
Wireless N Adapter RNX-N250UBE

Wireless N Adapter RNX-N250UBE

User Manual

 

 

 

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1)This device may not cause harmful interference.

2)This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

National Restrictions

2400.0-2483.5 MHz

Country

Restriction

 

 

Bulgaria

 

 

 

France

Outdoor use limited to 10 mW

 

e.i.r.p. within the band 2454-2483.5

 

MHz

 

 

Italy

 

 

 

Reason/remark

General authorization required for outdoor use and public service Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012

If used outside of own premises, general authorization is

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Wireless N Adapter RNX-N250UBE User ManualCountry Wireless N Adapter RNX-N250UBE2400.0-2483.5 MHz RestrictionWireless N Adapter RNX-N250UBE Table of Content 1.1 Overview of the Product Package ContentChapter 1 Overview You must have at least the following 1.2 Features1.3 System Requirement 1.4 Specification Chapter 2 Installation Guide 2.1 Software Installationz Click Next z Click Install to start installing z Follow the InstallShield Wizard steps, and click Finish when donez Now your PC or notebook will restart automatically Chapter 3 Wireless Connection Guide 3.1. Connecting with Microsoft Zero Configuration tool Win XP3.2. Connecting with Window 3.3. Connecting with Wireless LAN Utility 3.3.1 Step 1 Search Available Network 3.3.2 Step 2 Select and Add to ProfileAfter click “Add to Profile”, you will see the next window “Wireless Network Properties” popup with your current wireless signal’s setting. RNX-N180PCe will detect the current setting of your SSID. So after the “Wireless Network Properties” popup, all you need to do is to enter the password of your SSID and click OK to continute Chapter 4 Utility Configuration - Win XP’s Station Mode 4.1. GeneralOthers 4.2. ProfileNetwork Address z Create a new Infrastructure mode profilez Create a new ad-hoc mode profile 4.2.3 Edit created a profileSelect a profile which you want to copy and then click Duplicate 4.2.4 DuplicateModify the profile information according to your demand 4.2.5 Set default Import the new profile name in the popup window blank4.3. Available Network Double-click the network to which you wish to connect4.4. Status 4.5. Statistics 4.6. Wi-Fi Protect Setup 4.6.1 Method 1 PIN Input Config PINWPS config page 2. Click Pin Input ConfigPIN2. Click Start PBC on the AP-Router WPS config page 4.6.2 Method 2 Push Button1. Click Push Button ConfigPBC on Wi-Fi Protect Setup page Remark Page clients from trying to establish a BSS at the same time, which can result in multiple singular BSSs being established, rather than a single BSS with multiple clients associated to it
Top Page Image Contents