Rosewill user manual Wireless Adapter RNX-N4

Page 47

Wireless Adapter RNX-N4

User Manual

 

 

 

 

 

 

•Address Mode: L2TP can be used with a dynamic or static IP address. If you select the Dynamic IP radio button, then the IIP address in the next field is not required. However, if you select the Static IP radio button, then the IP address in the next field is required.

•L2TP Address: Specify the IP address

•L2TP Subnet Mask: Specify the subnet mask for the IP address.

•L2TP Gateway IP Address: Specify the IP address of the L2TP gateway.

•L2TP Server IP Address: If the L2TP Server’s IP address is different from the default gateway, then you may specify it here.

•User Name: Specify the user name which is provided by your ISP.

•Password: Specify the password which is provided by your ISP, and then verify it once again in the next field.

•Reconnect Mode: Select a reconnection time: Always on (A connection to the Internet is always maintained), On demand (A connection to the Internet is made as needed), Manual: You have to open up the Web-based management interface and click the Connect button manually any time that you wish to connect to the Internet.

•Maximum Idle Time: Time interval the machine can be idle before the PPTP connection is disconnected. The Maximum Idle Time value is only used for the "On demand" and "Manual" reconnect modes.

•Primary / Secondary DNS Address: Specify the primary and secondary IP address, which is assigned by your ISP.

•MTU: The Maximum Transmission Unit (MTU) is a parameter that determines the largest packet size (in bytes) that the router will send to the WAN. If LAN devices send larger packets, the router will break them into smaller packets. Ideally, you should set this to match the MTU of the connection to your ISP. Typical values are 1500 bytes for an Ethernet connection and 1492 bytes for a PPPoE connection. If the router's MTU is set too high, packets will be fragmented downstream. If the router's MTU is set too low, the router will fragment packets unnecessarily and in extreme cases may be unable to establish some connections. In either case, network performance can suffer.

•MAC Address: If you need to change the MAC address of the rounter's WAN-side Ethernet interface, either type in an alternate MAC address (for example, the MAC address of the router initially connected to the ISP) or click on Clone Your PCs MAC

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Wireless Router RNX-N4 Understanding the Hardware Wireless Adapter RNX-N4 SPI Features & BenefitsIntroduction Safety Guidelines Package ContentsFront Panel Wireless Soho Router DescriptionRear Panel Applications Network ConfigurationSystem Requirements Infrastructure Mode Understanding the Hardware Hardware InstallationIP Address Configuration Wireless Adapter RNX-N4 Logging Internet Connection WizardWireless Adapter RNX-N4 Dhcp Connection Dynamic IP Address PPPoE Point-to-Point Protocol over Ethernet Wireless Adapter RNX-N4 Pptp Point-to-Point Tunneling Protocol Wireless Adapter RNX-N4 4 L2TP Layer 2 Tunneling Protocol Static IP Address Configuration Wireless Adapter RNX-N4 ADD a Wireless Device WI-FI Protected Setup WizardWireless Adapter RNX-N4 Using the PIN Using the Push Button Wireless Network Setup Wireless Network Setup WizardAutomatic Network Setup Manual Network Setup Wireless Security Level Best WPA2 Wireless Adapter RNX-N4 Wireless Security Level Better WPA Wireless Security Level None Security Disabled Wireless Security Level Good WEP 64/128-BITWireless Adapter RNX-N4 Advanced WEB Configuration Basic WizardWirelessNetwork Settings Bridge Mode Wireless Settings Router ModeWireless Adapter RNX-N4 WEP Wired Equivalent Privacy Wireless Security ModeWPA Personal WI-FI Protected Access WPA Enterprise WI-FI Protected Access Pptp WAN SettingsStatic IP Address Configuration Dhcp Connection Dynamic IP Address AddressPppoe POINT-TO-POINT Protocol Over Ethernet Pptp POINT-TO-POINT Tunneling Protocol Maximum Idle Time4.2 L2TP Layer 2 Tunneling Protocol Wireless Adapter RNX-N4 Advanced Advanced WirelessWireless Adapter RNX-N4 Special Applications Virtual ServerPort Forwarding StreamEngine Wireless Adapter RNX-N4 Routing Access Control Wireless Adapter RNX-N4 Wireless Adapter RNX-N4 Address MAC Address Filter Web FilterFirewall Wireless Adapter RNX-N4 Advanced → Virtual Server Inbound Filter Wish Wi-Fi Protected Setup Advanced Network UPNP, WAN Ping… Wireless Adapter RNX-N4 Tools Time Zone SettingSystem Restore the Configuration from a File Save Configuration to a FileSystem Reboot Restore Settings to DefaultSystem Logs Firmware UpgradeSystem Check Dynamic DNSSchedules Status Wireless StatusStatistics Logs StatusWish Session Status Internet Session Status Wireless Adapter RNX-N4 Ascii Appendix a GlossaryAdsl CAT BootpDSL DhcpDMZ DNSGUI EAPFTP Ieee HttpHttps IcmpLAN IPXISP L2TPNIC MppeMTU NATRadius POP3PPP PptpSoho SIPSmtp SnmpUTP UDPURL USBWPA WispWlan Router and Gateway Appendix B SpecificationsRadio Specifications Hardware SummaryManagement NAT/ NaptImportant Note Appendix C FCC Interference StatementEnvironment & Physical

RNX-N4 specifications

The Rosewill RNX-N4 router is a versatile wireless networking device designed to provide reliable internet connectivity for home and small office environments. It is particularly well-suited for users who require a balance between performance, ease of use, and affordability.

One of the standout features of the RNX-N4 is its compliance with the IEEE 802.11n wireless standard. This standard enables the router to deliver a maximum wireless throughput of up to 300 Mbps, making it ideal for streaming videos, online gaming, and other bandwidth-intensive activities. It is also backward compatible with older wireless standards, such as 802.11g and 802.11b, ensuring that legacy devices can still connect seamlessly.

The Rosewill RNX-N4 utilizes MIMO (Multiple Input Multiple Output) technology, which enhances signal quality and range by using multiple antennas to transmit and receive data simultaneously. This results in better performance in environments with multiple obstacles or interference, ensuring a stable connection even at greater distances from the router.

Another notable characteristic of the RNX-N4 is its user-friendly setup. The router features a web-based user interface that simplifies the configuration process, making it accessible even for users with minimal technical expertise. Additionally, the router supports WPS (Wi-Fi Protected Setup), allowing users to quickly connect compatible devices to the network with the press of a button.

Security is a significant consideration for any networking device, and the RNX-N4 does not disappoint. It supports various modes of encryption, including WEP, WPA, and WPA2, ensuring that users can protect their wireless networks from unauthorized access. The router also features a built-in firewall that adds an additional layer of security against external threats.

The compact design of the Rosewill RNX-N4 makes it easy to position in various locations without taking up much space. It also features multiple Ethernet ports that allow users to connect wired devices for stable, high-speed internet access.

In summary, the Rosewill RNX-N4 is an affordable yet feature-rich wireless router that supports up to 300 Mbps speeds using MIMO technology. It is user-friendly, secure, and versatile enough to handle the demands of modern digital lifestyles. Whether for casual browsing or more intensive online activities, the RNX-N4 is a reliable choice for enhancing home and office connectivity.
Top Page Image Contents