Powerware 380/220V, 400/230V, 415/240V, 208/120V manual Mounting Template

Page 17

INSTALLATION

3.Attach the mounting bracket to the wall with appropriate wall anchors (not supplied). See the mounting template in Figure 3.

Verify that at least two wall anchors attach to studs within the wall.

376.5mm (14.82")

152.4 mm

16.8 mm

(6.00")

(0.66")

∅ 12.7 mm	∅ 5.3 mm
(0.50") TYP	(0.21") TYP

226.0 mm	283.5 mm
(8.90")	(11.16")

Figure 3. Mounting Template

4.Slide the loosened front screws on the electronics module into the slots on the mounting bracket.

5.Verify all screw holes are aligned. Reinstall the four screws removed in Step 2, but do not fully tighten. See Figure 2.

6.If installing the optional conduit box, continue to Step 7. Otherwise, proceed to Step 11.

7.Remove the front plate from each conduit box. Retain the plates and screws for later reinstallation. See Figure 4.

EATON Powerware® Energy Management System (EMS) Upgrade Kit User’s Guide S 164201724 Rev 1 www.powerware.com

Image 17

Contents Page Requesting a Declaration of Conformity Three−phase alternating current Special SymbolsPage Table of Contents Maintenance Serial Port Service −Slot CardSpecifications Troubleshooting WarrantyChapter Introduction Introduction Safety Warnings Important Safety InstructionsN G E R Consignes de sécuritéSicherheitswarnungen Wichtige Sicherheitsanweisungen AufbewarenL I G R O Advertencias de SeguridadUnpacking the Cabinet Inspecting the EquipmentChecking the Parts List Tools Required Wall Specifications Customer−Supplied Components Installing the HardwareMounting Template Conduit Box Option R N I N G Electrical ConnectionsCurrent Transformer Sizing Wire Tap SizingHarness Sizing Wiring Overview Example InstallationCT1 Panel Detail EMS−UGK−LV Model with Dual Panel Option Shown Main Input Harness Connections Branch Circuit Harness Connections Subfeed Monitoring Connections Install each CT around the appropriate subfeed breaker wireU T I O N Proceed to on Installation Power LED on the Power Xpert Gateway Series 1000 Card Microsoft Windows XP or Windows 2000 operating system Initial ConfigurationInstalling the Software Configuration Tool Click Connect to establish communication with the EMS−UGK Initial System ConfigurationSystem Status Page Connected Type the new name. Press Enter, then click Yes to confirm Installation Feature Setting Description Audible Horn Disabled Configure the following Building Alarm SettingsInstallation Configure the following settings for the selected panel Installation Initial Panel and Breaker Configuration Using the Display Installation Power Xpert Gateway Series 1000 Card Advanced Metering InstallationBoard UCB Reset FunctionBreaker Numbering Control Panel Functions Following table shows the indicator status and descriptionButtons to select another item on the screen to Display FunctionsMenu Map for Display Functions Menu MapFollowing tables show the basic menu structure Breaker Meters Panel MetersBuilding Alarm Setup OptionsConfiguring Panels Containing Branch Circuit Breakers Control Panel ConfigurationAccessing Configuration On the Panel Config screen, set the panel’s meter settings Configuring Panels Containing Subfeed BreakersNumber of subfeed breakers Overload Configuring Branch Circuit BreakersDelete Viewing Breaker Meters Viewing Panel MetersCommunication Communication Options Installing Communication FeaturesSerial Port Service −Slot Card Terminal ModeExternal Control Terminal Connections Control TerminalsProgrammable Signal Inputs Building Alarms Relay Output Contacts Alarm RelayCommunication Recycling the Used Equipment Chapter MaintenanceTo rewire and reconfigure the EMS−UGK Rewiring and Reconfiguring the InstallationCommunication Options Dimensions and WeightDisplay Optional Environmental and SafetyElectrical Input Panel Monitoring Rating Maximum 400A MeteringSpecifications Service and Support Typical Alarms and ConditionsTroubleshooting Powerware Energy Management System EMS Upgrade Kit Limited Factory WarrantyWarranty Page 164201724

415/240V, 380/220V, 208/120V, 400/230V specifications

The Powerware series of uninterruptible power supplies (UPS) is renowned for its versatility and reliability in providing essential power protection for critical equipment across various environments. Specifically, the configurations of 208/120V, 400/230V, 380/220V, and 415/240V cater to a wide range of geographic voltage standards, making it an ideal solution for diverse industrial and commercial applications.

One of the defining features of the Powerware UPS is its robust architecture which ensures high availability and reliability. Designed for mission-critical environments, these units often come equipped with advanced technologies that facilitate seamless operation during power interruptions or fluctuations.

The Powerware UPS employs double-conversion online technology that offers superior protection by continuously converting incoming AC power to DC and then back to AC. This process isolates the connected equipment from all power disturbances, such as surges, sags, and electrical noise, thus ensuring clean and stable output power. With this technology, users can rest assured that their sensitive electronics and IT infrastructure are shielded from any potential damage caused by irregular power supply.

Additionally, the Powerware series includes intelligent battery management systems that extend battery life and optimize performance. This feature involves real-time monitoring of battery health and automatic adjustment of charging methods to enhance efficiency. Users benefit from reduced maintenance costs and increased operational uptime due to improved battery management.

Moreover, the Powerware UPS is designed with scalability in mind. These units can be configured in parallel for load sharing, allowing organizations to expand their power capacity as needed without having to invest in entirely new systems. This flexibility is particularly beneficial for growing businesses that anticipate increased power needs over time.

The compact design and enhanced cooling systems further characterize the Powerware UPS, making it suitable for installations in space-constrained environments. The units are often equipped with user-friendly interfaces, providing easy access to critical information and diagnostics for power management.

In summary, the Powerware series with 208/120V, 400/230V, 380/220V, and 415/240V configurations represents a comprehensive solution for ensuring uninterrupted power supply in various settings. Its advanced technology, battery management features, scalability, and space-saving design make it an excellent choice for organizations seeking reliable power protection.