Powerware 400/230V, 380/220V, 415/240V Initial Panel and Breaker Configuration Using the Display

Page 40

INSTALLATION

Initial Panel and Breaker Configuration (Using the Display)

NOTE Use this section only if the optional display is installed.

Configure the panel and breaker data. You can use the following abbreviated instructions or follow the more detailed steps in Panel Configuration" on page 43.

1.From the setup screen, enter the Level 1 access password (default password is L1).

2.Select Meters then Panel, highlight the panel to configure, then select Config.

3.Set the Reset value to Yes and select OK to clear any breaker configuration settings for the panel.

4.Configure the following settings to match the physical panel:

Phases (always three−phase)

Breakers (the number of breakers in the panel) Rating (the rating in Amps of the main panel breaker) Panel Layout (panel numbering style)

5.Highlight the panel number and select Schedule.

6.Highlight the breaker to configure and select Config.

7.Configure the following settings to match the physical breaker:

Phases (number of phases for the breaker) Rating (breaker rating in Amps)

Warning (alarm warning level in %) Overload (alarm overload level in %) CT (the CT ratio – specify 71.9)

8.Configure each installed breaker in the panel.

9.If a second panel is installed, repeat the panel and breaker configuration for the second panel.

10.Activate the reset switch on the bottom of the electronics module: hold the switch for 10 seconds or until the display (if installed) turns off, then release the switch.

34 EATON Powerware® Energy Management System (EMS) Upgrade Kit User’s Guide S 164201724 Rev 1 www.powerware.com

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Page Requesting a Declaration of Conformity Special Symbols Three−phase alternating currentPage Table of Contents Serial Port Service −Slot Card MaintenanceSpecifications Troubleshooting WarrantyChapter Introduction Introduction Important Safety Instructions Safety WarningsConsignes de sécurité N G E RWichtige Sicherheitsanweisungen Aufbewaren SicherheitswarnungenAdvertencias de Seguridad L I G R OInspecting the Equipment Unpacking the CabinetChecking the Parts List Tools Required Installing the Hardware Wall Specifications Customer−Supplied ComponentsMounting Template Conduit Box Option Electrical Connections R N I N GWire Tap Sizing Current Transformer SizingWiring Overview Example Installation Harness SizingCT1 Panel Detail EMS−UGK−LV Model with Dual Panel Option Shown Main Input Harness Connections Branch Circuit Harness Connections Install each CT around the appropriate subfeed breaker wire Subfeed Monitoring ConnectionsU T I O N Proceed to on Installation Power LED on the Power Xpert Gateway Series 1000 Card Installing the Software Configuration Tool Initial ConfigurationMicrosoft Windows XP or Windows 2000 operating system Initial System Configuration Click Connect to establish communication with the EMS−UGKSystem Status Page Connected Type the new name. Press Enter, then click Yes to confirm Installation Configure the following Building Alarm Settings Feature Setting Description Audible Horn DisabledInstallation Configure the following settings for the selected panel Installation Initial Panel and Breaker Configuration Using the Display Installation Advanced Metering Installation Power Xpert Gateway Series 1000 CardBreaker Numbering Reset FunctionBoard UCB Following table shows the indicator status and description Control Panel FunctionsDisplay Functions Buttons to select another item on the screen toFollowing tables show the basic menu structure Menu MapMenu Map for Display Functions Panel Meters Breaker MetersSetup Options Building AlarmAccessing Configuration Control Panel ConfigurationConfiguring Panels Containing Branch Circuit Breakers Configuring Panels Containing Subfeed Breakers On the Panel Config screen, set the panel’s meter settingsNumber of subfeed breakers Configuring Branch Circuit Breakers OverloadDelete Viewing Panel Meters Viewing Breaker MetersCommunication Serial Port Service Installing Communication FeaturesCommunication Options Terminal Mode −Slot CardControl Terminals External Control Terminal ConnectionsRelay Output Contacts Alarm Relay Programmable Signal Inputs Building AlarmsCommunication Chapter Maintenance Recycling the Used EquipmentRewiring and Reconfiguring the Installation To rewire and reconfigure the EMS−UGKDimensions and Weight Communication OptionsElectrical Input Environmental and SafetyDisplay Optional Metering Panel Monitoring Rating Maximum 400ASpecifications Typical Alarms and Conditions Service and SupportTroubleshooting Limited Factory Warranty Powerware Energy Management System EMS Upgrade KitWarranty Page 164201724

415/240V, 380/220V, 208/120V, 400/230V specifications

The Powerware series of uninterruptible power supplies (UPS) is renowned for its versatility and reliability in providing essential power protection for critical equipment across various environments. Specifically, the configurations of 208/120V, 400/230V, 380/220V, and 415/240V cater to a wide range of geographic voltage standards, making it an ideal solution for diverse industrial and commercial applications.

One of the defining features of the Powerware UPS is its robust architecture which ensures high availability and reliability. Designed for mission-critical environments, these units often come equipped with advanced technologies that facilitate seamless operation during power interruptions or fluctuations.

The Powerware UPS employs double-conversion online technology that offers superior protection by continuously converting incoming AC power to DC and then back to AC. This process isolates the connected equipment from all power disturbances, such as surges, sags, and electrical noise, thus ensuring clean and stable output power. With this technology, users can rest assured that their sensitive electronics and IT infrastructure are shielded from any potential damage caused by irregular power supply.

Additionally, the Powerware series includes intelligent battery management systems that extend battery life and optimize performance. This feature involves real-time monitoring of battery health and automatic adjustment of charging methods to enhance efficiency. Users benefit from reduced maintenance costs and increased operational uptime due to improved battery management.

Moreover, the Powerware UPS is designed with scalability in mind. These units can be configured in parallel for load sharing, allowing organizations to expand their power capacity as needed without having to invest in entirely new systems. This flexibility is particularly beneficial for growing businesses that anticipate increased power needs over time.

The compact design and enhanced cooling systems further characterize the Powerware UPS, making it suitable for installations in space-constrained environments. The units are often equipped with user-friendly interfaces, providing easy access to critical information and diagnostics for power management.

In summary, the Powerware series with 208/120V, 400/230V, 380/220V, and 415/240V configurations represents a comprehensive solution for ensuring uninterrupted power supply in various settings. Its advanced technology, battery management features, scalability, and space-saving design make it an excellent choice for organizations seeking reliable power protection.
Top Page Image Contents