SUPER MICRO Computer 5016T-TB user manual Connector Definitions

Page 48

SUPERSERVER 5016T-TB User's Manual

5-9 Connector Definitions

ATX Power 24-pin Connector

Pin Definitions (JPW1)

Main ATX Power Supply

Connector

The 24-pin primary power supply connector (JPW1) meets the SSI EPS 12V specification. The 8-pin CPU PWR connector (JPW2) is also required for the processor. Refer to the table on the right for the pin definitions.

Pin# Definition

13+3.3V

14-12V

15COM

16PS_ON

17COM

18COM

19COM

20Res (NC)

21+5V

22+5V

23+5V

24COM

Pin # Definition

1+3.3V

2+3.3V

3COM

4+5V

5COM

6+5V

7COM

8PWR_OK

95VSB

10+12V

11+12V

12+3.3V

Processor Power Connector

JPW2 must also be connected to the power supply to provide power for the processor. See the table on the right for pin definitions.

Power Button

The power button (from the computer chassis) connects to pins 1 and 2 of JF1. See the table on the right for pin definitions.

Reset Button

The reset button (from the computer chassis) connects to pins 3 and 4 of JF1. See the table on the right for pin definitions.

Power Fail LED

The Power Fail LED connection is located on pins 5 and 6 of JF1. Re- fer to the table on the right for pin definitions.

+12V 8-pin Power

Pin Definitions (JPW2)

Pins Definition

1 - 4 Ground

5 - 8 +12V

Required Connection

Power Button

Pin Definitions (JF1)

Pin# Definition

1Power Signal

2Ground

Reset Button

Pin Definitions (JF1)

Pin# Definition

3Reset

4Ground

PWR Fail LED

Pin Definitions (JF1)

Pin# Definition

5Vcc

6Ground

5-14

Image 48
Contents Super Manual Revision 1.0a Release Date December 29 Preface About This ManualManual Organization Advanced Motherboard Setup Advanced Chassis SetupBios Preface Table of Contents System Safety Viii Advanced Chassis Setup Page Chapter Introduction OverviewMotherboard Features Intel X58/ICH10R Chipset System Block Diagram Server Chassis Features Contacting Supermicro HeadquartersEurope Asia-PacificPage Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the System FigureAccessing the Inside of the System Checking the Drive Bay Setup Checking the DrivesReset Button PowerChapter System Interface Control Panel ButtonsOverheat/Fan Fail HDDSerial ATA Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup Handling the ServerboardServerboard Installation UnpackingConnecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control PanelControl Panel Header Pins I/O PortsInstalling the Processor and Heatsink Installing an LGA1366 ProcessorCPU Installing a Passive CPU Heatsink Removing the Heatsink Installing Memory Modules Installing & Removing DIMMsMemory Support Maximum Memory PossibleAdding PCI Expansion Cards Possible System Memory Allocation & AvailabilityServerboard Details X8STi Layout Not drawn to scaleJumper Description Default Setting X8STi Quick ReferenceConnector Definitions HDD LED/UID Switch Power On LEDOverheat/Fan Fail/UID LED NMI Button Fan HeadersATX PS/2 Keyboard and PS/2 Mouse Ports Serial PortsChassis Intrusion Wake-On-LANExternal Speaker/Internal Buzzer Overheat/Fan Fail LEDPower Supply SMBus Header Onboard Power LEDUniversal Serial Bus USB Sgpio HeadersPower Supply Fail LED Header Alarm ResetButton Unit Identifier ButtonJumper Settings VGA Enable/DisableExplanation of Jumpers Cmos ClearLAN1/2 Enable/Disable Watch Dog Enable/DisableUSB Wake-Up Onboard Indicators BMC Enable/DisableSMBus to PCI Slots LAN1/2 LEDsOnboard Power LED LE1 BMC Heartbeat LEDFloppy Drive Connector Floppy and Sata PortsSata Ports Installing Software Supero Doctor Supero Doctor III Interface Display Screen Remote Control Page Chapter Advanced Chassis Setup Static-Sensitive DevicesControl Panel Chassis Front ViewSystem Fans System Fan FailureDrive Bay Installation/Removal Accessing the Drive BaysSerial ATA Drive Installation Mounting a Sata Drive in a Drive Carrier DVD-ROM Drive Installation Sata Power CablesPower Supply Power Supply FailurePage Starting Bios Setup Utility How To Change the Configuration DataChapter IntroductionMain Setup Starting the Setup UtilitySystem Time/System Date Processor System MemoryAdvanced Setup Configurations Xboot FeatureXProcessor & Clock Options Hardware Prefetcher Available when supported by the CPU Clock Spread SpectrumActive Processor Cores Intel Eist TechnologyIntel Turbo Boost Configuration Turbo Ratio Limit Program Core Ratio Limit~ 3 Core Ratio Limit TDC Limit OverrideXAdvanced Chipset Control Memory Mode QPI L0s and L1Memory Frequency Demand ScrubbingInlet Temperature Temperature RiseHigh Performance Event Timer Air FlowActive State Power Management Intel VT-dIntel I/OAT USB FunctionsIDE Detect Timeout sec Xide / Floppy ConfigurationFloppy a SATA#1 ConfigurationLBA/Large Mode PIO ModeType Block Multi-Sector TransferDMA Mode A.R.T. For Hard disk drives32Bit Data Transfer XPCI/PnP Configuration XRemote Access Configuration XSuper IO Device ConfigurationXHardware Health Configuration CPU Temperature/System Temperature System TemperatureCPU Temperature Xacpi Configuration XTrusted Computing Xipmi Configuration X8STi-F/X8STi-3F OnlyClear BMC System Event Log Set LAN ConfigurationSet PEF Configuration AbledXEvent Log Configuration Security Settings Supervisor PasswordUser Password Change Supervisor PasswordBoot Configuration XBoot Device PriorityBoot Sector Virus Protection Exit Options XHard Disk DrivesXRemovable Drives XCD/DVD DrivesLoad Optimal Defaults Load Fail-Safe DefaultsDiscard Changes and Exit Discard ChangesAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B Installing the Windows OS Installing Windows on RAID SystemsInstalling Windows on Non-RAID Systems Appendix C System Specifications ProcessorsChassis Appendix C System Specifications

5016T-TB specifications

The Super Micro Computer 5016T-TB is a powerful and versatile server chassis designed to meet the increasing demands of data centers and enterprise environments. Tailored for high-performance computing, it combines a robust architecture with advanced technologies, making it an ideal choice for various applications, including cloud computing, virtualization, and mission-critical workloads.

One of the standout features of the 5016T-TB is its compact form factor, which optimizes space in server racks while providing exceptional performance. The chassis supports dual Intel Xeon processors, allowing users to harness substantial computing power for processing complex tasks. Additionally, it accommodates up to 512GB of DDR3 ECC memory, ensuring data integrity and stability, crucial for applications in need of reliability.

The server is equipped with six hot-swap drive bays, supporting both SAS and SATA drives, which allows for rapid data access and redundancy. This design contributes to enhanced data security and availability, as swapping out drives can be done without interrupting operations. The 5016T-TB supports multiple RAID configurations, providing users with flexible options for storage management and fault tolerance.

With a focus on connectivity, the Super Micro 5016T-TB features several PCI Express slots, enabling users to expand functionality with additional networking or storage cards. It comes with onboard Intel Gigabit Ethernet ports, ensuring high-speed network connections essential for data-intensive applications. The server chassis is also designed for efficient cooling, incorporating optimized airflow patterns to maintain optimal operating temperatures, which prolongs the lifespan of components and enhances overall performance.

In terms of energy efficiency, the 5016T-TB is compliant with various environmental standards and features advanced power management technologies. This not only reduces operational costs but also decreases the carbon footprint of the data center.

Another significant characteristic of this server is its management capabilities. Supermicro provides dedicated management tools for monitoring system health, temperature, and power consumption, which are essential for proactive infrastructure management.

With its robust build, substantial scalability, and advanced features, the Super Micro Computer 5016T-TB stands out as a reliable option for businesses looking to enhance their computing infrastructure. Whether for virtualized environments or resource-intensive applications, it represents a commitment to delivering high performance and flexibility for diverse IT needs.