SUPER MICRO Computer 5016T-TB Universal Serial Bus USB, Sgpio Headers, Power Supply SMBus Header

Page 52

SUPERSERVER 5016T-TB User's Manual

Universal Serial Bus (USB)

There are two Universal Serial Bus

Universal Serial Bus Pin Definitions (USB)

ports located on the I/O panel. An additional six USB headers are in- cluded on the board, which may be used for front side access (cables not included). USB 6 and USB 7 are "Type A" connectors. See the table on the right for pin definitions.

USB0/1

Pin # Definition

1+5V

2PO-

3PO+

4Ground

5N/A

USB4/5/6/7

Pin # Definition

1+5V

2PO-

3PO+

4Ground

5Key

SGPIO Headers

SGPIO Header

Pin Definitions (T-SGPIO-0/T-TGPIO-1)

The SGPIO (Serial General Purpose Input/Output) headers are used to communicate with an enclosure man- agement chip on the backplane. See the table on the right for pin defini- tions.

Pin# Definition

1 NC

3 Ground

5 Load

7 Clock

Pin

2

4

6

8

Definition

NC

DATA Out

Ground

NC

Power Supply SMBus Header

A Power SMB header is located at SMB_PS1. Connect the appropriate cable here to utilize SMB on your system. See the table on the right for pin definitions.

Onboard Power LED

An onboard Power LED header is located at JLED. This header con- nects to the control panel header (JF1) to indicate the status of system power. See the table on the right for pin definitions.

NC = No Connection

Power Supply SMB

Header Pin Definitions

(SMB_PS1)

Pin# Definition

1Clock

2Data

3PWR Fail

4Ground

5+3.3V

Onboard PWR LED

Pin Definitions (JLED)

Pin# Definition

1VCC

2No Connection

3Connection to PWR LED in JF1

5-18

Image 52
Contents Super Manual Revision 1.0a Release Date December 29 About This Manual PrefaceManual Organization Advanced Chassis Setup Advanced Motherboard SetupBios Preface Table of Contents System Safety Viii Advanced Chassis Setup Page Chapter Introduction OverviewMotherboard Features Intel X58/ICH10R Chipset System Block Diagram Server Chassis Features Contacting Supermicro HeadquartersEurope Asia-PacificPage Preparing for Setup Chapter Server InstallationUnpacking the System Choosing a Setup Location Rack PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the System FigureAccessing the Inside of the System Checking the Drive Bay Setup Checking the DrivesReset Button PowerChapter System Interface Control Panel ButtonsOverheat/Fan Fail HDDSerial ATA Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup Handling the ServerboardServerboard Installation UnpackingConnecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control PanelControl Panel Header Pins I/O PortsInstalling the Processor and Heatsink Installing an LGA1366 ProcessorCPU Installing a Passive CPU Heatsink Removing the Heatsink Installing Memory Modules Installing & Removing DIMMsMemory Support Maximum Memory PossibleAdding PCI Expansion Cards Possible System Memory Allocation & AvailabilityServerboard Details X8STi Layout Not drawn to scaleJumper Description Default Setting X8STi Quick ReferenceConnector Definitions Power On LED HDD LED/UID SwitchOverheat/Fan Fail/UID LED NMI Button Fan HeadersATX PS/2 Keyboard and PS/2 Mouse Ports Serial PortsChassis Intrusion Wake-On-LANExternal Speaker/Internal Buzzer Overheat/Fan Fail LEDPower Supply SMBus Header Onboard Power LEDUniversal Serial Bus USB Sgpio HeadersPower Supply Fail LED Header Alarm ResetButton Unit Identifier ButtonJumper Settings VGA Enable/DisableExplanation of Jumpers Cmos ClearWatch Dog Enable/Disable LAN1/2 Enable/DisableUSB Wake-Up Onboard Indicators BMC Enable/DisableSMBus to PCI Slots LAN1/2 LEDsOnboard Power LED LE1 BMC Heartbeat LEDFloppy and Sata Ports Floppy Drive ConnectorSata Ports Installing Software Supero Doctor Supero Doctor III Interface Display Screen Remote Control Page Chapter Advanced Chassis Setup Static-Sensitive DevicesControl Panel Chassis Front ViewSystem Fans System Fan FailureAccessing the Drive Bays Drive Bay Installation/RemovalSerial ATA Drive Installation Mounting a Sata Drive in a Drive Carrier DVD-ROM Drive Installation Sata Power CablesPower Supply Power Supply FailurePage Starting Bios Setup Utility How To Change the Configuration DataChapter IntroductionStarting the Setup Utility Main SetupSystem Time/System Date Processor System MemoryAdvanced Setup Configurations Xboot FeatureXProcessor & Clock Options Hardware Prefetcher Available when supported by the CPU Clock Spread SpectrumActive Processor Cores Intel Eist TechnologyIntel Turbo Boost Configuration Turbo Ratio Limit Program Core Ratio Limit~ 3 Core Ratio Limit TDC Limit OverrideXAdvanced Chipset Control Memory Mode QPI L0s and L1Memory Frequency Demand ScrubbingInlet Temperature Temperature RiseHigh Performance Event Timer Air FlowActive State Power Management Intel VT-dIntel I/OAT USB FunctionsIDE Detect Timeout sec Xide / Floppy ConfigurationFloppy a SATA#1 ConfigurationLBA/Large Mode PIO ModeType Block Multi-Sector TransferA.R.T. For Hard disk drives DMA Mode32Bit Data Transfer XPCI/PnP Configuration XRemote Access Configuration XSuper IO Device ConfigurationXHardware Health Configuration System Temperature CPU Temperature/System TemperatureCPU Temperature Xacpi Configuration XTrusted Computing Xipmi Configuration X8STi-F/X8STi-3F OnlyClear BMC System Event Log Set LAN ConfigurationSet PEF Configuration AbledXEvent Log Configuration Security Settings Supervisor PasswordUser Password Change Supervisor PasswordXBoot Device Priority Boot ConfigurationBoot Sector Virus Protection Exit Options XHard Disk DrivesXRemovable Drives XCD/DVD DrivesLoad Optimal Defaults Load Fail-Safe DefaultsDiscard Changes and Exit Discard ChangesAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B Installing the Windows OS Installing Windows on RAID SystemsInstalling Windows on Non-RAID Systems Appendix C System Specifications ProcessorsChassis Appendix C System Specifications

5016T-TB specifications

The Super Micro Computer 5016T-TB is a powerful and versatile server chassis designed to meet the increasing demands of data centers and enterprise environments. Tailored for high-performance computing, it combines a robust architecture with advanced technologies, making it an ideal choice for various applications, including cloud computing, virtualization, and mission-critical workloads.

One of the standout features of the 5016T-TB is its compact form factor, which optimizes space in server racks while providing exceptional performance. The chassis supports dual Intel Xeon processors, allowing users to harness substantial computing power for processing complex tasks. Additionally, it accommodates up to 512GB of DDR3 ECC memory, ensuring data integrity and stability, crucial for applications in need of reliability.

The server is equipped with six hot-swap drive bays, supporting both SAS and SATA drives, which allows for rapid data access and redundancy. This design contributes to enhanced data security and availability, as swapping out drives can be done without interrupting operations. The 5016T-TB supports multiple RAID configurations, providing users with flexible options for storage management and fault tolerance.

With a focus on connectivity, the Super Micro 5016T-TB features several PCI Express slots, enabling users to expand functionality with additional networking or storage cards. It comes with onboard Intel Gigabit Ethernet ports, ensuring high-speed network connections essential for data-intensive applications. The server chassis is also designed for efficient cooling, incorporating optimized airflow patterns to maintain optimal operating temperatures, which prolongs the lifespan of components and enhances overall performance.

In terms of energy efficiency, the 5016T-TB is compliant with various environmental standards and features advanced power management technologies. This not only reduces operational costs but also decreases the carbon footprint of the data center.

Another significant characteristic of this server is its management capabilities. Supermicro provides dedicated management tools for monitoring system health, temperature, and power consumption, which are essential for proactive infrastructure management.

With its robust build, substantial scalability, and advanced features, the Super Micro Computer 5016T-TB stands out as a reliable option for businesses looking to enhance their computing infrastructure. Whether for virtualized environments or resource-intensive applications, it represents a commitment to delivering high performance and flexibility for diverse IT needs.