SUPER MICRO Computer X6DHi-G2 ROM Scan Ordering, Reset Configuration Data, Option ROM Scan

Page 66

X6DH3-G2/X6DHi-G2 User's Manual

ROM Scan Ordering

This feature allows the user to decide which Option ROM to be activated fi rst. The options are Onboard first and Add-On fi rst.

Reset Configuration Data

If set to Yes, this setting clears the Extended System Confi guration Data- (ESCD) area. The options are Yes and No.

Frequency for Slot#2-Slot#3/MASS, Frequency for PCI-X Slot#4 (Note: MASS=Mass Storage Devices: SATA, SAS and SCSI. SAS is for the X6DH3-G2 only.)

This option allows the user to change the bus frequency for the devices installed in the slot indicated. The options are Auto, PCI 33 MHz, PCI 66 MHz, PCI-X 66 MHz, and PCI-X 100 MHz.

Frequency for PCI-X#1 On Riser, Frequency for PCI-X#2-#3 On Riser

(*Available when a 2U Active Riser Card is present.)

This option allows the user to change the bus frequency of the devices installed in the slot indicated. The options are Auto, PCI 33 MHz, PCI 66 MHz, PCI-X 66 MHz, PCI-X 100 MHz, and PCI-X 133 MHz.

￿PCI 33MHz Slot#1, PCI-X 100MHz Slot#2, PCI-X 100MHz ZCR Slot#3,

PCI-X 133MHz Slot#4, PCI-Exp x8 Slot#5, PCI-Exp x8 Slot#5, PCI- Exp x8 Slot#6 (or PCI-Exp x8 Slot#6 and Riser, if a 2U Active Riser Card is present.)

Access the submenu for each of the settings above to make changes to the following:

Option ROM Scan

When enabled, this setting will initialize the device expansion ROM. The options are Enabled and Disabled.

Enable Master

This setting allows you to enable the selected device as the PCI bus master. The options are Enabled and Disabled.

Latency Timer

This setting allows you to set the clock rate for Bus Master. A high-priority, high- throughout device may benefi t from a greater clock rate. The options are Default, 0020h, 0040h, 0060h, 0080h, 00A0h, 00C0h, and 00E0h. For Unix, Novell and other Operating Systems, please select the option: other. If a drive fails after the installation of a new software, you might want to change this setting and try again. a different operating system requires a different Bus Master clock rate.

4-10

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Super Reproductive harm About This Manual Manual Organization Conventions Used in the ManualTable of Contents Troubleshooting SMBBios AppendicesChecklist OverviewEurope Contacting Super MicroHeadquarters Asia-PacificX6DH3-G2/X6DHi-G2 Image Super Jumper Description Default Setting Connector DescriptionQuick Reference X6DH3-G2/X6DHi-G2 Motherboard Features Onboard I/O Acpi FeaturesDimensions OtherBlock Diagram of the E7520 Chipset 6300ESB System Features 6300ESB ICH System FeaturesChipset Overview Special Features PC Health MonitoringMain Switch Override Mechanism Acpi FeaturesSlow Blinking LED for Suspend-State Indicator CPU Overheat LED and Fan Fail ControlExternal Modem Ring-On Power SupplySuper I/O Wake-On-LAN WOLIntroduction Page Precautions Static-Sensitive DevicesUnpacking Xeon Processor and Heatsink Installation CPU InstallationCEK Heatsink Installation To Un-install the Heatsink PGA604 Socket Empty and with Processor Installed Mounting the Motherboard in the ChassisInstalling DIMMs Dimm Installation See -2 onMemory Support I/OPorts/Control Panel Connectors Release TabJF1 Header Pins Front Control PanelPin and 8-pin Power Connectors Connecting CablesATX Power Connector Pin12V CPU PWR Pin ATX PWR Pin 12V PWRNMI Button Power LEDPower LED Pin Definitions JF1 NMI Button Pin Definitions JF1NIC1/NIC2 LED Indicators HDD LEDPower Fail LED Overheat/FanFail LEDReset Button Pin Definitions JF1 Reset ButtonPower Button Power Button Pin Definitions JF1Chassis Intrusion Pin Definitions JL1 Chassis IntrusionSerial Ports Serial Port Pin DefinitionsUSB 0/1 Universal Serial Bus USBUniversal Serial Bus Pin Definitions FP USB 2/3KB/Mouse Glan Giga-bit Ethernet PortsATX PS/2 Keyboard PS/2 Mouse Ports PS/2 Keyboard Mouse Port Pin DefinitionsPower LED/Speaker Fan HeadersWake-On-Ring Pin Definitions Wake-On-RingWake-On-LAN Wake-On-LAN Pin DefinitionsPower SMB I2 C Connector SMB Header Pin DefinitionsAdaptec SAS SMB Power I2C Connector *For the X6DH3-G2 only SASACTOutput Pin DefinitionsSAS SMB PWR Pin Definitions Power Supply Failure LED Overheat LED JOHPWR Supply Fail LED Pin Definitions Glan Enable Jumper Settings Jumper SettingsGlan Enable/Disable Glan 1 Enable Glan 2 EnableCmos Clear Watch Dog EnableWatch Dog Jumper Settings JWD Watch Dog Clear CmosVGA Enable/Disable Alarm Reset JAR3rd PWR Supply PWR Fault Detect J3P SAS Controller Enable *For the X6DH3-G2 onlyPower Force On Enable Disable Power Force On Enable/Disable Jumper SettingsPWR Force-On Onboard Indicators Glan LEDsAdaptec SAS Activity LED Indicators For the X6DH3 SAS ActLEDConnector Parallel Printer PortParallel Port Floppy Connector FloppyIDE Connectors BalePage No Power Troubleshooting ProceduresBefore Power On No VideoTechnical Support Procedures Memory ErrorsLosing the System’s Setup Configuration Frequently Asked Questions Question How do I update my BIOS?Returning Merchandise for Service Question Whats on the CD that came with my motherboard?Starting the Setup Utility System BiosHow To Change the Configuration Data IntroductionRunning Setup Main Bios SetupʳPress the Delete key to enter Setup Main Bios Setup Menu Main Setup FeaturesSerial ATA RAID Enable Native Mode OperationSerial ATA Multi-Sector Transfer LBA Mode ControlType Bit I/OUltra DMA Mode Advanced SetupTransfer Mode System MemoryQuiet Boot Boot FeaturesQuick Boot Mode Acpi ModeCache Base 0-512K Memory Cache Cache System Bios AreaCache Video Bios Area Cache Base 512K-640KDiscrete Mtrr Allocation Default Primary Video AdapterPCI Parity Error Forwarding PCI ConfigurationLatency Timer Reset Configuration DataEnable Master ROM Scan OrderingClock Spectrum Feature Large Disk Access ModeForce Compliance Mode Delayed Transaction DiscardUSB Function Serr Signal ConditionEnabling Multi-Media Timer Legacy USB SupportProcessor Power Management Thermal Management 2 *Available when supported by the CPUCPU and the OS Onboard COM Device ConfigurationKBC Clock Input Base I/O AddressDMI Event Logging DMA ChannelFloppy Disk Controller Event Log ValidityBaud Rate Console RedirectionCOM Port Address Console TypeN12V P12V Hardware Monitor Logic CPU Temperature ThresholdVcore A/Vcore B P3V3 P5VsbSet Supervisor Password Supervisor Password IsUser Password Is SecuritySet User Password Fixed Disk Boot SectorPassword on Boot Cdrom Drive Boot+Removable Devices +Hard DriveExit Page Monitor type does not match Cmos Run Setup Keyboard errorKeyboard locked Unlock key switch System battery is dead Replace and run SetupReal time clock error System Cmos checksum bad Default configuration usedSystem timer error Check date and time settingsAllocation Error for device System cache error Cache disabledFail-Safe Timer NMI Failed Entering SetupDevice IRQ conflict PS/2 Mouse Boot Summary ScreenInvalid System Configuration Data Nnnn kB Extended RAM PassedSystem Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup Video Bios shadowedPage Recoverable Post Errors Terminal Post ErrorsPost Code Description Post Code Description Post Code Description Post Code Description Post Code Description Page ATA Operate Mode Introduction to the Intel 6300ESB I/O Controller HubCombined Mode Enhanced ModeAppendix C Software Installation Using the Adaptec RAID Configuration Utility ARC Using the Array Configuration Utility ACUAdaptec Embedded Serial ATA with HostRAID Controller Driver Managing Arrays Viewing Array Properties Deleting ArraysCreating Arrays To create an arrayAssigning Array Properties To assign properties to the new arrayRaid Level Create Via When Appropriate Page Adding a Bootable Array Deleting a Bootable ArrayInitializing Disk Drives To initialize drivesPage Page Rebuilding Arrays To Rebuild an arrayUsing the Adaptec RAID Configuration Utility ARC Using the Array Configuration Utility ACUManaging Arrays Viewing Array PropertiesDeleting Arrays Assigning Array Properties Adding a Bootable Array To initialize drives To Rebuild an arrayTo access the SAS utilities To Set Controller Configuration To Set Physical Configuration Using the Disk Utilities To Exit Adaptec RAID Configuration Utility SAS is for the X6DH3-G2 only Installing Other Software Programs and Drivers Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control

X6DH3-G2, X6DHi-G2 specifications

Super Micro Computer is renowned for its innovation in the server and workstation market, and the X6DH3-G2 and X6DHi-G2 motherboards are prime examples of their commitment to performance, reliability, and advanced technology. These motherboards are designed to cater to the demands of enterprise-level applications, offering robust support for a variety of workloads.

The X6DH3-G2 and X6DHi-G2 motherboards are based on the Intel E7501 chipset, supporting the Intel Xeon processor family. This allows for significant computing power, making them ideal choices for data-centric applications in various fields, from scientific research to database management. One of the standout features of these motherboards is their dual-processor capability, enabling users to harness the power of two Xeon CPUs simultaneously for enhanced multitasking and performance.

In addition to dual-processor support, both motherboards offer up to 64 GB of DDR2 ECC memory. This ensures data integrity and system stability, which are crucial in enterprise environments. The presence of ECC (Error-Correcting Code) memory allows these motherboards to automatically detect and correct data corruption, significantly reducing the risk of system crashes and data loss.

Storage capabilities are another highlight of the X6DH3-G2 and X6DHi-G2 motherboards. They come equipped with multiple SATA and SCSI interfaces, ensuring compatibility with various storage solutions. This flexibility allows users to configure their storage according to their specific needs, whether it be for high-speed access or large-capacity requirements. RAID (Redundant Array of Independent Disks) support is also integrated, enabling users to implement data redundancy and improve performance.

Networking features are robust, with integrated gigabit Ethernet that ensures high-speed connections and efficient data transfer. This is essential for applications demanding low latency and high bandwidth.

The layout of the X6DH3-G2 and X6DHi-G2 motherboards is designed for optimal thermal management and airflow, enhancing system longevity and reliability. They also support a range of expansion slots, including PCI Express, which allows for the addition of graphics cards and other advanced peripherals.

Super Micro’s commitment to quality is evident in these motherboards, showcasing reliability and a wealth of features that make them suitable for demanding enterprise environments. With a focus on performance, scalability, and stability, the X6DH3-G2 and X6DHi-G2 motherboards are engineered to meet the evolving challenges faced by IT professionals and organizations today.
Top Page Image Contents