SUPER MICRO Computer X8SIL-V, X8SIL-F user manual

Page 64

Chapter 3: Troubleshooting

Answer: To solve this issue, disable the IPMI jumper. Another solution is to use a USB floppy drive instead of the onboard floppy drive. For the IPMI jumper location, please check Chapter 1.

Question: Why can't I format a floppy disk in Windows or why does it take too long to format a floppy disk on the X8SIL-F or X8SIE-F/X8SI6-F motherboard?

Answer: This is maybe because C State Technology is enabled in the BIOS. Please go to the BIOS (Advanced -> Processor & Clock options -> Intel ® C- STATE tech), and select “disable”.

Question: What is the heat sink part number for my X8SIL/X8SIL-F/X8SIL-V, X8SIE/X8SIE-F/X8SIE-LN4 or X8SI6-F motherboard?

Answer: For the 1U passive heat sink, ask for SNK-P0046P (back plate is included), for the 2U active heat sink, SNK-P0046A4.

Question: Does the PCI-E slots on the X8SIL/X8SIL-F/X8SIL-V, X8SIE/X8SIE-F/ X8SIE-LN4 or X8SI6-F motherboard support graphic cards?

Answer: Yes they do, but not Slot 6 and Slot 7 on the X8SIL motherboard. This is due to Intel chipset limitations.

Question: Why can't I recover the BIOS even when I’ve followed the instructions in the user’s manual for X8SIL-F or X8SIE-F?

Answer: Please disable the IPMI jumper and try it again. For the jumper loca- tion, please check Chapter 1.

Question: My floppy drive returns an error when installing drivers during Windows installation or BIOS recovery on my X8SIL-F or X8 SIE-F motherboard, what shall I do?

Answer: Please disable the IPMI jumper and try it again. For the jumper loca- tion, please check Chapter 1. If you are installing Windows Vista or Windows 7, you may also use a USB drive in lieu of a floppy drive.

Question: My built-in floppy interface is disabled by default. What is the reason for this?

Answer: This is due to an Intel limitation where a conflict exists with the floppy drive in C-States C4~C7. Therefore, when enabling the floppy disk drive in- terface, C-States C4~C7 will be disabled automatically to prevent a conflict. If both a floppy disk drive and C-States C4~C7 (enabled) are needed, we recommend to leave the internal floppy interface at disabled and use a USB floppy drive instead. For more on Intel C-State architecture, please see Page 4-7 of the BIOS Chapter.

3-5

Page 63 Page 65
Image 64
Page 63 Page 65
Contents X8SIL X8SIL-F X8SIL-V Page About This Motherboard Manual Organization Conventions Used in the ManualEurope Contacting SupermicroAsia-Pacific Table of Contents Troubleshooting Introduction Main Setup Advanced Setup Configurations Installing DriversChecklist OverviewMotherboard Image X8SIL-F Shown Motherboard Layout VGA111 121 131 141 151 X8SIL/X8SIL-F/X8SIL-V Headers/Connectors Number Description Description Color/State StatusMotherboard Features Power Configuration Devices USB Devices X8SIL-F/X8SIL-V OnlyKeyboard/Mouse Serial COM PortsCD Utilities DimensionsOther Block Diagram RoHS 6/6 X8SIL/X8SIL-F/X8SIL-V System Block DiagramIntel 3400/3420 Chipset Features Chipset OverviewPower Configuration Settings PC Health MonitoringPower Supply Slow Blinking LED for Suspend-State IndicatorBios Support for USB Keyboard Main Switch Override MechanismSuper I/O ISCSI SupportOverview of the Nuvoton BMC Controller Static-Sensitive Devices PrecautionsUnpacking Processor and Heatsink Installation Installing the LGA1156 ProcessorPage Page Installing a Passive CPU Heatsink Removing the Heatsink Installing an Active Fan CPU Heatsink Page Active Heatsink Removal Dimm Installation Installing DDR3 MemoryMemory Support DDR3 ECC Registered Rdimm Memory Support Memory Population GuidelinesPopulated Any combination Per Channel Installing and Removing DIMMs To RemovePossible System Memory Allocation & Availability Tools Needed Motherboard InstallationLocation of Mounting Holes Installation Instructions Connectors/IO Ports Back Panel Connectors and IO PortsATX PS/2 Keyboard and PS/2 Mouse Ports MouseKeyboard Keyboard Purple Mouse GreenUniversal Serial Bus USB DefinitionsEthernet Ports NC No Connection LAN1 LAN2 Ipmi Dedicated LAN X8SIL- F onlySerial Ports COM1 COM2Video Connector VGAJF1 Header Pins Front Control PanelPower LED Front Control Panel Pin DefinitionsOverheat OH/Fan Fail OH/Fan FailPower Button Reset ButtonReset Button PWR Button Connecting Cables ATX Main PWR & CPU PWR ConnectorsRequired Pin ATX Main PWR Pin Processor PWRFan Headers Chassis IntrusionInternal Buzzer SpeakerTPM Header Internal Buzzer Speaker Header TPM HeaderPower Supply I2C Connector Onboard Power LEDDOM PWR Connector Sgpio 0/1 Headers Two T-SGPIO Serial-Link General PurJumper Settings LAN Port Enable/DisableLAN Port 1 Enable B. LAN Port 2 Enable Explanation of JumpersCmos Clear PCI Slot SMB EnableClear Cmos JI2C1 JI2C2 Energy Saving Enable VGA EnableVGA Enable Energy Saving Enable BP USB 0/1 Wake-up BMC Enable BMC EnableUSB Wake-Up Onboard Indicators LAN 1/LAN 2 LEDsIpmi Dedicated LAN LEDs LAN PortIpmi Heartbeat LED X8SIL-F Only Unsupported Memory LEDSata and Floppy Drive Connections Sata ConnectionsP O R T a N T Note on X8SIL-F motherboards Floppy ConnectorFloppy Troubleshooting Procedures Before Power OnNo Power No VideoMemory Errors Technical Support ProceduresLosing the System’s Setup Configuration Question How do I update my BIOS? Frequently Asked QuestionsQuestion What type of memory does my motherboard support? Question Whats on the CD that came with my motherboard? Page Battery Removal Battery Removal and InstallationBattery Installation Returning Merchandise for Service Page How To Change the Configuration Data Starting Bios Setup UtilityIntroduction Main Setup How to Start the Setup UtilityProcessor System Time/System DateSystem Memory Advanced Setup Configurations BOOT FeatureWait For F1 If Error Power Button FunctionRestore on AC Power Loss Hit Del Message DisplayHardware Prefetcher Available when supported by the CPU Processor & Clock OptionsCPU Ratio Clock Spread SpectrumActive Processor Cores Intel Eist TechnologyC1E Support Intel C-STATE TechAdvanced Chipset Control SATA / Floppy Configuration IDE Detect Timeout sec LBA/Large ModePIO Mode TypeDMA Mode A.R.T. For Hard disk drivesPCI/PnP Configuration Super IO Device Configuration Remote Access ConfigurationHardware Health Configuration System Temperature CPU TemperatureFan Speed Control Modes ACPI Configuration Trusted Computing IPMI Configuration X8SIL-F Only Event Log Configuration Intel TXT LT Configuration Intel TXT InitializationSecurity Settings Supervisor PasswordUser Password Change Supervisor PasswordBoot Device Priority Boot SettingsBoot Sector Virus Protection Retry Boot Devices Exit OptionsRemovable Drives CD/DVD DrivesLoad Optimal Defaults Load Fail-Safe DefaultsDiscard Changes and Exit Discard ChangesX8SIL/X8SIL-F/X8SIL-V Appendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Installing Drivers Driver/Tool Installation Display ScreenConfiguring SuperDoctor SuperDoctor III Interface Display Screen-II Remote Control Page Recovery Process from a USB Device/Drive Recommended Method Part 1 Boot Sector Recovery ProcessRecovery Process from an IDE/SATA Atapi Disc Drive Part 2 Bios Reprogramming Re-Flashing
Related manuals
Manual 101 pages 31.8 Kb

X8SIL-V, X8SIL-F, X8SIL specifications

SUPER MICRO Computer X8SIL, X8SIL-F, and X8SIL-V are advanced server motherboards designed to meet the demanding needs of today's data centers and enterprise environments. These motherboards from Supermicro deliver exceptional performance, scalability, and reliability, making them suitable for a wide range of applications, including virtualization, cloud computing, and database management.

One of the main features of the X8SIL series is its compatibility with Intel's Xeon 5500 and 5600 series processors. This allows users to harness the power of multi-core technology, ensuring optimal performance for both single-threaded and multi-threaded applications. With support for up to 144GB of DDR3 ECC memory, the X8SIL motherboards provide ample memory bandwidth, enhancing the overall system performance and efficiency.

The X8SIL-F variant includes an integrated IPMI (Intelligent Platform Management Interface) feature, which enables remote management and monitoring of the system. This technology allows IT administrators to proactively manage server health, perform remote troubleshooting, and ensure minimal downtime. Additionally, the X8SIL-F supports Supermicro's Green Computing technology, which helps reduce power consumption and enhance energy efficiency, leading to lower operational costs.

In terms of storage, the X8SIL series offers multiple SATA and SAS interface options, facilitating a wide range of storage configurations. The motherboards feature six SATA II ports and optional SAS capabilities, allowing users to implement RAID setups for improved performance and data redundancy. This flexibility in storage solutions is crucial for environments that require high availability and reliability.

The X8SIL motherboard series is equipped with a range of I/O ports, including multiple USB ports, PCI Express slots, and Gigabit Ethernet interfaces. This extensive connectivity ensures that users can easily expand and customize their systems according to specific application needs. The onboard Gigabit Ethernet ports provide fast network access, which is essential for data-intensive workloads.

Furthermore, the X8SIL, X8SIL-F, and X8SIL-V boast an efficient thermal design. These motherboards feature robust heat sinks and fan headers, which help maintain optimal operating temperatures, even under heavy workloads. This thermal efficiency is critical in extending the lifespan of components and ensuring consistent performance.

In summary, SUPER MICRO Computer's X8SIL, X8SIL-F, and X8SIL-V motherboards stand out with their strong performance, advanced management features, flexible storage options, and efficient thermal design. These characteristics make them ideal choices for businesses looking to build reliable and scalable data center solutions.
Top Page Image Contents