SUPER MICRO Computer X9SVL-IIF, X9SCM-IIF user manual Installing the Motherboard

Page 43

Chapter 2: Installation

Installing the Motherboard

1.Install the I/O shield into the chassis.

2.Locate the mounting holes on the motherboard.

3.Locate the matching mounting holes on the chassis. Align the mounting holes on the motherboard against the mounting holes on the chassis.

4.Install standoffs in the chassis as needed.

5.Install the motherboard into the chassis carefully to avoid damaging mother- board components.

6.Using the Philips screwdriver, insert a Pan head #6 screw into a mounting hole on the motherboard and its matching mounting hole on the chassis.

7.Repeat Step 5 to insert #6 screws into all mounting holes.

8.Make sure that the motherboard is securely placed in the chassis.

Note: Images displayed are is for illustration only. Your chassis or compo- nents might look different from those shown in this manual.

2-17

Image 43
Contents X9SCM-IIF X9SCL-IIF Page About This Motherboard Manual Organization PrefaceConventions Used in This Manual Asia-Pacific Contacting SupermicroHeadquarters EuropeTable of Contents Vii Chapter Troubleshooting Bios RAID Network Device BBS Priorities, Hard Drive BBS Priorities Appendix a Bios Error Beep Codes Overview ChecklistMotherboard Image X9SCM-IIF Motherboard Image X9SCL-IIF COM2 Motherboard LayoutX9SCM-IIF/X9SCL-IIF Quick Reference X9SCM-IIF/X9SCL-IIF Jumpers Jumper Label Description DefaultConnector Label Description X9SCM-IIF/X9SCL-IIF Headers/ConnectorsCPU Motherboard FeaturesBios System Block Diagram X9SCM-IIF/X9SCL-IIF Block DiagramChipset Overview Intel C202/C204 Express Chipset FeaturesPC Health Monitoring Special FeaturesPower Supply Acpi FeaturesSlow Blinking LED for Suspend-State Indicator Manageability Engine ME Advanced Power Management for -F Models OnlyIntel Intelligent Power Node Manager NM Super I/OOverview of the Nuvoton WPCM450 Controller Standardized Warning Statements Battery Handlingةعناصلا ةمرشلا تاميلعحل اقفو ةلمعحسملا تايراطبلا نم صلخج 製品の廃棄 Product DisposalStatic-Sensitive Devices PrecautionsUnpacking Installing the LGA1155 Processor Processor and Heatsink InstallationLoad Plate Load Lever North Center Edge South Center Edge CPU properly installed Load lever locked Into place Screw#1 Screw#2 Motherboard Mounting Holes Installing a Passive CPU HeatsinkHeatsink Bracket Removing the Heatsink Installing an Active Fan CPU Heatsink Page Unplug PWR cord Active Heatsink RemovalDimm Installation Installing DDR3 MemoryRemoving Memory Modules DIMM1A Memory SupportMemory Population Guidelines DIMM1B DIMM2APossible System Memory Allocation & Availability DDR3 Unbuffered ECC Udimm MemoryPhilips Screwdriver Motherboard InstallationTools Needed Location of Mounting HolesInstalling the Motherboard Back I/O Panel Connectors/IO PortsBack I/O Panel PS/2 Keyboard/Mouse Pin Definitions ATX PS/2 Keyboard/Mouse PortsFront Panel USB 2/3, 4/5, 12/13 Pin Definitions Universal Serial Bus USBLAN Ports Pin Definition Ethernet PortsCOM1 COM2 Serial PortsVGA/CRT Pin Definitions Video ConnectorFront Control Panel JF1 Header PinsFront Control Panel Pin Definitions Power LEDHDD LED Overheat OH/Fan Fail/Front NIC1/NIC2 LAN1/LAN2Power Button Reset ButtonATX Main PWR & CPU PWR Connectors Connecting CablesPin Main PWR Chassis Intrusion Fan HeadersSpeaker Internal BuzzerPower Supply I2C Connector Onboard Power LEDTPM Header Sgpio 1/2 HeadersStand-by Power DOM PWR ConnectorLAN Port Enable/Disable Jumper SettingsExplanation of Jumpers Clear Cmos PCI Slot SMB EnableWatch Dog Enable VGA EnableUSB Wake-Up BMC EnableBios Recovery ME RecoveryLAN1 LAN2 Onboard IndicatorsIpmi LAN Unsupported Memory LED Power Standby LEDIpmi Heartbeat LED Sata Connections Sata Connectors Pin DefinitionsPage Before Power On Troubleshooting ProceduresNo Power Losing the System’s Setup Configuration Memory ErrorsNo Video Technical Support Procedures Frequently Asked Questions Page Battery Battery Lock Battery Holder Battery Removal and InstallationBattery Removal Proper Battery Disposal Battery InstallationReturning Merchandise for Service Page How To Change the Configuration Data Starting Bios Setup UtilityIntroduction How to Start the Setup Utility Main SetupProcessor System Time/System DateSystem Memory BOOT Feature Advanced Setup ConfigurationsProcessor & Clock Options Eist Hardware Prefetcher Available when supported by the CPUPower Technology Intel AES-NIC1E Support Chipset Configuration CPU Bridge ConfigurationTurbo Mode CPU C3 Report, CPU C6 Report, CPU 7 ReportSouth Bridge Configuration Integrated IO ConfigurationIDE IDE/SATA ConfigurationAhci RAID PCIe/PCI/PnP ConfigurationSerial Port 1 / Serial Port Super IO Device ConfigurationBoot Graphics Adapter Priority Serial Port1 Settings/ Serial Port2 SettingsConsole Redirection Settings Serial Port Console Redirection ConfigurationCOM0/COM1/SOL Console Redirection Whea Support ACPI SettingsHigh Precision Event Timer Acpi Sleep StateEvent Logs Change Smbios Event Log SettingsMeci Metw System Event Log Ipmi ConfigurationErasing Settings Erase SEL When SEL is FullBMC Network Configuration Boot Settings Delete Boot Option Administrator Password Security SettingsUser Password Discard Changes and Exit Restore DefaultsSave & Exit Options Save Changes and ExitRestore User Defaults Save As User DefaultsBoot Override Beep Code/LED Error Message Description Bios Error Beep CodesPage Driver/Tool Installation Display Screen Installing DriversConfiguring SuperDoctor SuperDoctor III Interface Display Screen-II Remote Control Page How to Recover the Uefi Bios Image -the Main Bios Block An Overview to the Uefi BiosTo Recover the Main Bios Block Using a USB-Attached Device Page Page