SMC Networks SMC8724ML3 Optional Media Extender Modules, Extender Module LEDs, 10G Xenpak Module

Page 28

ABOUT THE TIGERSTACK 1000

Optional Media Extender Modules

10G Xenpak Module

10G Xenpak Module

Diag

Link/Activity

Figure 1-6 Single-Port 10G Module (Xenpak)

The module Xenpak slot supports all standard 10 Gigabit Ethernet (10G) Xenpak transceivers. All 10GBASE transceivers operate at 10 Gbps full duplex.

Extender Module LEDs

The optional slide-in 10G module includes its own integrated LED indicators on the module panel. The following table describes the LEDs.

		Table 1-3 Module LEDs
LED	Condition		Status
Link/	On/Flashing		Port has a valid link at 10 Gbps. Flashing indicates
Activity	Green		activity.
	Off		There is no link on the port.

Diag	Flashing Green		System self-diagnostic test in progress.

	Green		System self-diagnostic test successfully completed.

	Amber		System self-diagnostic test has detected a fault.

1-8

Image 28

Contents TigerStack Page TigerStack Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Compliances FCC Class aIndustry Canada Class a Japan Vcci Class aCE Mark Declaration of Conformance for EMI and Safety EEC Safety Compliance Power Cord SafetyAustralia AS/NZS 3548 1995 Class a Warnhinweis Faseroptikanschlüsse Optische SicherheitPower Cord Set Vii France et Pérou uniquementViii SchukoEnvironmental Statement Audience PurposeRelated Publications Table of Contents Making Network Connections XiiAppendices XiiiTables XivFigures Xvi FiguresChapter About Tigerstack OverviewSwitch Architecture Front PanelsNetwork Management Options Description of Hardware10/100/1000BASE-T Ports SFP Slots Stacking PortsPort and System Status LEDs Port LEDs Port Status LEDsSystem Status LEDs Optional Redundant Power Unit Power Supply SocketsOptional Media Extender Modules Extender Module LEDs10G Xenpak Module Module LEDsFeatures and Benefits ConnectivityExpandability PerformanceManagement Introduction to Switching Chapter Network PlanningApplication Examples Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsUsing Layer 3 Routing IP Routing for Unicast TrafficApplication Notes Network Planning Installing the Switch Selecting a SiteEthernet Cabling RJ-45 ConnectionsPackage Contents Equipment ChecklistOptional Rack-Mounting Equipment Mounting Rack MountingAttaching the Brackets Montage Rack Mounting German Rack-MontageDesktop or Shelf Mounting Attaching the Adhesive FeetInstalling an Optional Module into the Switch Installing an Optional ModuleInstalling an Optional SFP Transceiver into the Switch Inserting an SFP Transceiver into a SlotConnecting Switches in a Stack Making Stacking Connections Stacking Topologies Connecting to a Power Source Power SocketWiring Map for Serial Cable Connecting to the Console PortWiring Map for Serial Cable Connecting Network Devices Chapter Making Network ConnectionsTwisted-Pair Devices Cabling GuidelinesConnecting to PCs, Servers, Hubs and Switches Making Twisted-Pair ConnectionsNetwork Wiring Connections Wiring Closet ConnectionsFiber Optic SFP Devices Gbps Fiber Optic Connections Making Connections to SFP TransceiversConnecting to Xenpak Transceiver Connectivity Rules 1000BASE-T Cable RequirementsGbps Ethernet Collision Domain Maximum 10GBASE-SR 10 Gigabit Ethernet Cable LengthMbps Gigabit Ethernet Collision Domain Mbps Fast Ethernet Collision Domain Mbps Ethernet Collision DomainMaximum 1000BASE-ZX Fiber Optic Cable Length Maximum Fast Ethernet Cable LengthCable Labeling and Connection Records Diagnosing Switch Indicators Appendix a TroubleshootingTable A-1 Troubleshooting Chart Diagnosing Power Problems with the LEDs Table A-2 Power/RPU LEDsInstallation Power and Cooling ProblemsIn-Band Access Stack Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments Table B-1 10/100BASE-TX MDI and MDI-X Port PinoutsStraight-Through Wiring Figure B-2 Straight-through WiringCrossover Wiring Figure B-3 Crossover Wiring1000BASE-T Pin Assignments Cable Testing for Existing Category 5 CableTable B-2 1000BASE-T MDI and MDI-X Port Pinouts Adjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber StandardsAppendix C Specifications Physical CharacteristicsSwitching Database WeightTemperature Power SupplySwitch Features Management FeaturesSafety StandardsCompliances CE Mark EmissionsExtender Modules Warranty10G Extender Module Xenpak Specifications Table D-1 TigerStack 1000 Products and Accessories Appendix D Ordering InformationOrdering Information Glossary-1 Glossary1000BASE-T Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Index-1Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call