SMC Networks SMC8748ML3 Compliances, FCC Class a, Industry Canada Class a, Japan Vcci Class a

Page 7

COMPLIANCES

FCC - Class A

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart B of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) cable for RJ-45 connections—Category 3 or greater for 10 Mbps connections, Category 5 or better for 100 Mbps connections, and Category 5 or 5e for 1000 Mbps connections. Use 50/125 or 62.5/125 micron multimode fiber optic cable, or 9/125 micron single-mode cable, for fiber-optic transceiver connections.

Warnings: 1. Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment.

2.When connecting this switch to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent elec- trical hazards.

Industry Canada - Class A

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques,” NMB-003 édictée par le ministère des Communications.

Japan VCCI Class A

iii

Image 7
Contents TigerStack Page TigerStack Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Japan Vcci Class a CompliancesFCC Class a Industry Canada Class aCE Mark Declaration of Conformance for EMI and Safety EEC Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety CompliancePower Cord Safety Australia AS/NZS 3548 1995 Class aPower Cord Set France et Pérou uniquement ViiSchuko ViiiEnvironmental Statement Audience PurposeRelated Publications Table of Contents Xii Making Network ConnectionsXiii AppendicesXiv TablesFigures Figures XviOverview Chapter About TigerstackFront Panels Switch ArchitectureNetwork Management Options Description of Hardware10/100/1000BASE-T Ports Stacking Ports SFP SlotsPort LEDs Port Status LEDs Port and System Status LEDsSystem Status LEDs Power Supply Sockets Optional Redundant Power UnitModule LEDs Optional Media Extender ModulesExtender Module LEDs 10G Xenpak ModulePerformance Features and BenefitsConnectivity ExpandabilityManagement Chapter Network Planning Introduction to SwitchingCollapsed Backbone Application ExamplesNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsIP Routing for Unicast Traffic Using Layer 3 RoutingApplication Notes Network Planning Selecting a Site Installing the SwitchRJ-45 Connections Ethernet CablingPackage Contents Equipment ChecklistOptional Rack-Mounting Equipment Rack Mounting MountingAttaching the Brackets Rack-Montage Montage Rack Mounting GermanAttaching the Adhesive Feet Desktop or Shelf MountingInstalling an Optional Module Installing an Optional Module into the SwitchInserting an SFP Transceiver into a Slot Installing an Optional SFP Transceiver into the SwitchConnecting Switches in a Stack Making Stacking Connections Stacking Topologies Power Socket Connecting to a Power SourceWiring Map for Serial Cable Connecting to the Console PortWiring Map for Serial Cable Cabling Guidelines Connecting Network DevicesChapter Making Network Connections Twisted-Pair DevicesMaking Twisted-Pair Connections Connecting to PCs, Servers, Hubs and SwitchesWiring Closet Connections Network Wiring ConnectionsFiber Optic SFP Devices Making Connections to SFP Transceivers Gbps Fiber Optic ConnectionsConnecting to Xenpak Transceiver Maximum 10GBASE-SR 10 Gigabit Ethernet Cable Length Connectivity Rules1000BASE-T Cable Requirements Gbps Ethernet Collision DomainMbps Gigabit Ethernet Collision Domain Maximum Fast Ethernet Cable Length Mbps Fast Ethernet Collision DomainMbps Ethernet Collision Domain Maximum 1000BASE-ZX Fiber Optic Cable LengthCable Labeling and Connection Records Diagnosing Switch Indicators Appendix a TroubleshootingTable A-1 Troubleshooting Chart Table A-2 Power/RPU LEDs Diagnosing Power Problems with the LEDsInstallation Power and Cooling ProblemsIn-Band Access Stack Troubleshooting Twisted-Pair Cable and Pin Assignments Appendix B CablesTable B-1 10/100BASE-TX MDI and MDI-X Port Pinouts 10BASE-T/100BASE-TX Pin AssignmentsFigure B-2 Straight-through Wiring Straight-Through WiringFigure B-3 Crossover Wiring Crossover Wiring1000BASE-T Pin Assignments Cable Testing for Existing Category 5 CableTable B-2 1000BASE-T MDI and MDI-X Port Pinouts Fiber Standards Adjusting Existing Category 5 Cabling to Run 1000BASE-TPhysical Characteristics Appendix C SpecificationsPower Supply Switching DatabaseWeight TemperatureManagement Features Switch FeaturesCE Mark Emissions SafetyStandards CompliancesExtender Modules Warranty10G Extender Module Xenpak Specifications Appendix D Ordering Information Table D-1 TigerStack 1000 Products and AccessoriesOrdering Information Glossary-1 Glossary1000BASE-T Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index-1 IndexIndex-2 Index-3 Index-4 Page For Technical SUPPORT, Call