SMC Networks SMC8724ML3, SMC8748ML3 CE Mark Declaration of Conformance for EMI and Safety EEC

Page 8

COMPLIANCES

CE Mark Declaration of Conformance for EMI and Safety (EEC)

SMC contact for these products in Europe is:

SMC Networks Europe, Edificio Conata II,

Calle Fructuós Gelabert 6-8, 2o, 4a,

08970 - Sant Joan Despí, Barcelona, Spain.

This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the compliance with these Directives, the following standards were applied:

RFI Emission:	• Limit class A according to EN 55022:1998
	• Limit class A for harmonic current emission according to
	EN 61000-3-2/1995
	• Limitation of voltage fluctuation and flicker in low-voltage supply
	system according to EN 61000-3-3/1995
Immunity:	• Product family standard according to EN 55024:1998
	• Electrostatic Discharge according to EN 61000-4-2:1995
	(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)
	• Radio-frequency electromagnetic field according to EN 61000-4-3:1996
	(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)
	• Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/
	DC power supply: ±1 kV, Data/Signal lines: ±0.5 kV)
	• Surge immunity test according to EN 61000-4-5:1995
	(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)
	• Immunity to conducted disturbances, Induced by radio-frequency
	fields: EN 61000-4-6:1996 (0.15 - 80 MHz with
	1 kHz AM 80% Modulation: 3 V/m)
	• Power frequency magnetic field immunity test according to
	EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)
	• Voltage dips, short interruptions and voltage variations immunity test
	according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%
	Reduction @500 ms, >95% Reduction @5000 ms)
LVD:	• EN60950:2000

Warning: Do not plug a phone jack connector in the RJ-45 port. This may damage this device.

Attention: Les raccordeurs ne sont pas utilisés pour le système téléphonique!

iv

Image 8

Contents TigerStack Page TigerStack Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Compliances FCC Class aIndustry Canada Class a Japan Vcci Class aCE Mark Declaration of Conformance for EMI and Safety EEC Safety Compliance Power Cord SafetyAustralia AS/NZS 3548 1995 Class a Warnhinweis Faseroptikanschlüsse Optische SicherheitPower Cord Set Vii France et Pérou uniquementViii SchukoEnvironmental Statement Related Publications PurposeAudience Table of Contents Making Network Connections XiiAppendices XiiiTables XivFigures Xvi FiguresChapter About Tigerstack OverviewSwitch Architecture Front Panels10/100/1000BASE-T Ports Description of HardwareNetwork Management Options SFP Slots Stacking PortsPort and System Status LEDs Port LEDs Port Status LEDsSystem Status LEDs Optional Redundant Power Unit Power Supply SocketsOptional Media Extender Modules Extender Module LEDs10G Xenpak Module Module LEDsFeatures and Benefits ConnectivityExpandability PerformanceManagement Introduction to Switching Chapter Network PlanningApplication Examples Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsUsing Layer 3 Routing IP Routing for Unicast TrafficApplication Notes Network Planning Installing the Switch Selecting a SiteEthernet Cabling RJ-45 ConnectionsOptional Rack-Mounting Equipment Equipment ChecklistPackage Contents Mounting Rack MountingAttaching the Brackets Montage Rack Mounting German Rack-MontageDesktop or Shelf Mounting Attaching the Adhesive FeetInstalling an Optional Module into the Switch Installing an Optional ModuleInstalling an Optional SFP Transceiver into the Switch Inserting an SFP Transceiver into a SlotConnecting Switches in a Stack Making Stacking Connections Stacking Topologies Connecting to a Power Source Power SocketWiring Map for Serial Cable Connecting to the Console PortWiring Map for Serial Cable Connecting Network Devices Chapter Making Network ConnectionsTwisted-Pair Devices Cabling GuidelinesConnecting to PCs, Servers, Hubs and Switches Making Twisted-Pair ConnectionsNetwork Wiring Connections Wiring Closet ConnectionsFiber Optic SFP Devices Gbps Fiber Optic Connections Making Connections to SFP TransceiversConnecting to Xenpak Transceiver Connectivity Rules 1000BASE-T Cable RequirementsGbps Ethernet Collision Domain Maximum 10GBASE-SR 10 Gigabit Ethernet Cable LengthMbps Gigabit Ethernet Collision Domain Mbps Fast Ethernet Collision Domain Mbps Ethernet Collision DomainMaximum 1000BASE-ZX Fiber Optic Cable Length Maximum Fast Ethernet Cable LengthCable Labeling and Connection Records Table A-1 Troubleshooting Chart Appendix a TroubleshootingDiagnosing Switch Indicators Diagnosing Power Problems with the LEDs Table A-2 Power/RPU LEDsIn-Band Access Power and Cooling ProblemsInstallation Stack Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments Table B-1 10/100BASE-TX MDI and MDI-X Port PinoutsStraight-Through Wiring Figure B-2 Straight-through WiringCrossover Wiring Figure B-3 Crossover WiringTable B-2 1000BASE-T MDI and MDI-X Port Pinouts Cable Testing for Existing Category 5 Cable1000BASE-T Pin Assignments Adjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber StandardsAppendix C Specifications Physical CharacteristicsSwitching Database WeightTemperature Power SupplySwitch Features Management FeaturesSafety StandardsCompliances CE Mark Emissions10G Extender Module Xenpak WarrantyExtender Modules Specifications Table D-1 TigerStack 1000 Products and Accessories Appendix D Ordering InformationOrdering Information 1000BASE-T GlossaryGlossary-1 Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Index-1Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call