SMC Networks SMC6724L3 INT manual Attaching the Brackets

Page 42

INSTALLING THE SWITCH

To rack-mount devices:

1.Attach the brackets to the device using the screws provided in the Bracket Mounting Kit.

Figure 3-1. Attaching the Brackets

2.Mount the device in the rack, using four rack-mounting screws (not provided).

Figure 3-2. Installing the Switch in a Rack

3.If installing a single switch only, turn to “Connecting to a Power Source” at the end of this chapter.

4.If installing multiple switches, mount them in the rack, one below the other, in any order.

3-4

Image 42

Contents TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Compliances FCC Class aIndustry Canada Class a EC Conformance Declaration Class a Japan Vcci Class a Australia AS/NZS 3548 1995 Class a Safety Compliance Warnhinweis Faseroptikanschlüsse Optische SicherheitUnderwriters Laboratories Compliance Statement Wichtige Sicherheitshinweise Germany Viii Table of Contents Installing the Switch Making Network ConnectionsAppendices Table of Contents Chapter About Tigerswitch 10/100 OverviewSwitch Architecture SMC6724L3 Front and Rear PanelsManagement Options Description of Hardware RJ-45 PortsPorts Status LEDs Port Status LEDsSystem Status LEDs System Status LEDsOptional Media Extender Modules Optional 10/100/1000BASE-T Module SMC6824GTOptional 100BASE-FX Module SMC6824FSSC Optional 100BASE-FX Module SMC6824FMSC Optional 1000BASE-X Gbic Module SMC6824GBOptional Redundant Power Unit Power Supply ReceptacleFeatures and Benefits ConnectivityExpandability Performance ManagementAbout the Tigerswitch 10/100 Introduction to Switching Chapter Network PlanningApplication Examples Collapsed BackboneCentral Wiring Closet Central Wiring ClosetRemote Connection with Fiber Cable Remote Connection with Fiber CableMaking Vlan Connections Making Vlan ConnectionsUsing Layer 3 Routing IP Routing for Unicast TrafficConnectivity Rules Mbps Gigabit Ethernet Collision Domain10/100 Mbps Ethernet Collision Domain Application Notes Network Planning Installing the Switch Selecting a SiteEquipment Checklist Package ContentsOptional Rack-Mounting Equipment Mounting Rack MountingAttaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive FeetInstalling an Optional Module into the Switch Installing an Optional ModuleInstalling a Gbic Transceiver Installing a Gbic TransceiverConnecting to a Power Source Power ReceptacleTwisted-Pair Devices Connecting Network DevicesChapter Making Network Connections Cabling GuidelinesConnecting to PCs, Servers, Hubs and Switches Making Twisted-Pair ConnectionsTWISTED-PAIR Devices Wiring Closet Connections Wiring Closet ConnectionsFiber Optic Devices Making SC Port Connections Appendix a Troubleshooting Diagnosing Switch IndicatorsPower and Cooling Problems InstallationIn-Band Access Specifications Appendix B CablesTwisted-Pair Cable and Pin Assignments Fiber SMFFigure B-1. RJ-45 Connector Pin Numbers 10BASE-T/100BASE-TX Pin AssignmentsStraight-Through Wiring Crossover Wiring1000BASE-T Pin Assignments Cable Testing for Existing Category 5 Cable Adjusting Existing Category 5 Cabling1000BASE-T Cable Requirements Wiring Map for Serial Cable Console Port Pin AssignmentsCables Appendix C Specifications Physical CharacteristicsBase Unit Compliances Warranty Slide-in Modules100BASE-FX Extender Modules 1000BASE-T Extender Module Model1000BASE-X Gbic Module Specifications Appendix D Ordering Information Ordering Information Glossary 1000BASE-TCollision Auto-NegotiationBandwidth Collision DomainFull Duplex Fast Ethernet SwitchFast Ethernet Gigabit EthernetLAN Segment Media Access Control MACIeee 802.3z Link SegmentRJ-45 Connector Switched PortsStraight-through Port Glossary-6 Index NumericsIndex-2 Index-3 Index-4 Page For Technical SUPPORT, Call