SMC Networks SMC6724L3 INT manual Compliances, FCC Class a, Industry Canada Class a

Page 7

COMPLIANCES

FCC - Class A

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart B of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) cable for RJ-45 connections—Category 3 or greater for 10 Mbps connections, Category 5 for 100 Mbps connections, and Category 5, 5e, or 6 for 1000 Mbps. Use 50/125 or 62.5/125 micron multimode fiber optic cable, or 9/125 micron single-mode fiber optic cable, for SC or ST-type connections.

Warnings: 1. Wear an anti-static wrist strap or take other suitable measures to prevent electro- static discharge when handling this equipment.

2.When connecting this switch to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards.

Industry Canada - Class A

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques,” NMB-003 édictée par le ministère des Communications.

iii

Image 7
Contents TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA FCC Class a CompliancesIndustry Canada Class a EC Conformance Declaration Class a Japan Vcci Class a Australia AS/NZS 3548 1995 Class a Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety ComplianceUnderwriters Laboratories Compliance Statement Wichtige Sicherheitshinweise Germany Viii Table of Contents Making Network Connections Installing the SwitchAppendices Table of Contents Overview Chapter About Tigerswitch 10/100SMC6724L3 Front and Rear Panels Switch ArchitectureManagement Options RJ-45 Ports Description of HardwarePort Status LEDs Ports Status LEDsSystem Status LEDs System Status LEDsOptional 10/100/1000BASE-T Module SMC6824GT Optional Media Extender ModulesOptional 100BASE-FX Module SMC6824FSSC Optional 1000BASE-X Gbic Module SMC6824GB Optional 100BASE-FX Module SMC6824FMSCPower Supply Receptacle Optional Redundant Power UnitConnectivity Features and BenefitsExpandability Management PerformanceAbout the Tigerswitch 10/100 Chapter Network Planning Introduction to SwitchingCollapsed Backbone Application ExamplesCentral Wiring Closet Central Wiring ClosetRemote Connection with Fiber Cable Remote Connection with Fiber CableMaking Vlan Connections Making Vlan ConnectionsIP Routing for Unicast Traffic Using Layer 3 RoutingMbps Gigabit Ethernet Collision Domain Connectivity Rules10/100 Mbps Ethernet Collision Domain Application Notes Network Planning Selecting a Site Installing the SwitchPackage Contents Equipment ChecklistOptional Rack-Mounting Equipment Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingInstalling an Optional Module Installing an Optional Module into the SwitchInstalling a Gbic Transceiver Installing a Gbic TransceiverPower Receptacle Connecting to a Power SourceCabling Guidelines Connecting Network DevicesChapter Making Network Connections Twisted-Pair DevicesMaking Twisted-Pair Connections Connecting to PCs, Servers, Hubs and SwitchesTWISTED-PAIR Devices Wiring Closet Connections Wiring Closet ConnectionsFiber Optic Devices Making SC Port Connections Diagnosing Switch Indicators Appendix a TroubleshootingInstallation Power and Cooling ProblemsIn-Band Access Appendix B Cables SpecificationsFiber SMF Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments Figure B-1. RJ-45 Connector Pin NumbersCrossover Wiring Straight-Through Wiring1000BASE-T Pin Assignments Adjusting Existing Category 5 Cabling Cable Testing for Existing Category 5 Cable1000BASE-T Cable Requirements Console Port Pin Assignments Wiring Map for Serial CableCables Physical Characteristics Appendix C SpecificationsBase Unit Compliances Slide-in Modules Warranty100BASE-FX Extender Modules Model 1000BASE-T Extender Module1000BASE-X Gbic Module Specifications Appendix D Ordering Information Ordering Information 1000BASE-T GlossaryCollision Domain Auto-NegotiationBandwidth CollisionGigabit Ethernet Fast Ethernet SwitchFast Ethernet Full DuplexLink Segment Media Access Control MACIeee 802.3z LAN SegmentSwitched Ports RJ-45 ConnectorStraight-through Port Glossary-6 Numerics IndexIndex-2 Index-3 Index-4 Page For Technical SUPPORT, Call