Checking the cutting unit’s parallelism | Husqvarna 15T AWD specification

Maintenance

Checking the cutting unit’s parallelism

Check the cutting unit’s parallelism as follows:

1Check the air pressure in the tyres 60 kPa/0.6 kp/cm2/8.5 PSI.

2Place the machine on a ﬂat surface.

3Put the lifting lever in the mowing position.

4Measure the distance between the ground and the front and rear edges of the cutting unit hood. The cutting unit should have a slight slant, with the rear edge 2-4 mm (1/ 8”) higher than the front edge.

Adjusting the parallelism of the cutting unit

1Remove the front hood and right-hand fender.

2Undo the nuts on the lift strut.

3Screw out (extend) the stay to raise the rear edge of the cover.

Screw in (shorten) the stay to lower the rear edge of the cover.

4Tighten the nuts after adjustment.

5On completion of the adjustment the unit’s parallelism should be re-checked.

6Fit the right-hand fender and the front hood.

Replacing the cutting unit belts

	!	WARNING! Wear gloves to protect your
	!	hands when working with the blades.
		hands when working with the blades.

There is a risk of crush injuries when working with the belt.

On these cutting units with collision-proof blades, the blades are driven by one V-belt. Do as follows to change the V-belt:

1Remove the cutting unit.

2Open the lock for the track rod bolt.

3 Remove the bolt so the track rod is released in one end.

4 Unscrew the bolt holding the unit frame bracket.

5Remove the lock and pass the unit frame out.

6Remove the two bolts on the unit frame.

English – 27

Image 27

Husqvarna 15T AWD, 15Ts AWD manual Checking the cutting unit’s parallelism, Adjusting the parallelism of the cutting unit

Contents

English Rider 15T Rider 15T AWD Rider 15Ts AWD Contents Service journal Pre-delivery serviceAfter the ﬁrst 8 hours Introduction Symbols KEY to Symbols KEY to Symbols What is what on the ride-on mower What is WHAT? General use Safety InstructionsSafety instructions Insure your Rider This is what you do Driving on slopes Children Maintenance Transport Presentation Lights Cutting height adjustment leverCutting unit Lifting lever for the cutting unit Clutch control Rider 15T AWD and Rider 15Ts AWD Exercise care and refuel outdoors see safety instructionsFuelling Release lever Driving Before startingStart the engine Remove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Driving the Rider Stop the engine Cutting tips Maintenance schedule Maintenance Cleaning Checking and adjusting the steering wiresRemoving of the machine hoods Adjusting the parking brake Rider 15T Checking and adjusting of throttle wireCan result in reduced braking ability Cool before starting to replace the air ﬁlter Checking and adjusting the choke wireReplacement of fuel ﬁlter Replacing the air ﬁlter Checking the fuel pump’s air ﬁlter Ignition systemReplacing the spark plug Check the safety system Checking the engine’s cooling air intake Replacing the light bulbsMain fuse Checking the tyre pressure Lift up the cutting unit When the engine is running. Mind your ﬁngersFitting the cutting head Trapping your hand Removing the cutting unit Replacing the cutting unit belts Adjusting the parallelism of the cutting unitHands when working with the blades Checking the cutting unit’s parallelism Placing in the service position Service position for the cutting unit CombiClip 103, CombiClip Restoring from service positionChecking the blades Removing the BioClip plug Replacing the engine oil LubricationChecking the engine’s oil level Changing the oil ﬁlter Lubricating the belt adjuster Checking the transmission oil levelGeneral lubrication Problem Procedure Troubleshooting schedule Guard ServiceStorage Winter storage Technical data Cutting unit CombiClip EC-declaration of conformity Applies to Europe only EC-declaration of conformityEN ISO 12100-2, EN-836 Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨