Checking the blades, Removing the BioClip plug | Husqvarna 15Ts AWD

Maintenance

Restoring from service position

1Grip the front edge of the unit and loosen the lock, fold down and slide in the unit.

2Replace the cutting height stay and the belt.

3 Tension the belt with the belt adjuster.

4 Fit the front cover.

Checking the blades

To achieve the best mowing results it is important that the blades are undamaged and well-sharpened.

Check that the blades’ attachment screws are tight.

IMPORTANT INFORMATION Replacing or sharpening the blades should be conducted by an authorised service workshop.

The blades should be balanced after sharpening.

Damaged blades should be replaced when hitting obstacles that result in a breakdown. Let the servicing dealer judge whether the blade can be repaired/ground or must be discarded.

Removing the BioClip plug

To change a Combi unit from BioClip function to cutting unit with rear ejection, remove the BioClip plug located under the unit with three screws.

CombiClip 103, CombiClip 112

1Put the unit in the service position, see Placing in the service position.

2Remove the three screws holding the BioClip plug, and remove the plug.

3Tip: Fit three full-thread screws M8x15 mm in the screw holes to protect the threads.

4Replace the unit in normal position.

Fit the BioClip plug in the reverse order.

CombiClip 94

1Put the unit in the service position, see Service position for the cutting unit.

2Loosen the knob holding the BioClip-plug and remove the plug.

3 Replace the unit in normal position.

English – 29

Image 29

Husqvarna 15Ts AWD, 15T AWD Checking the blades, Removing the BioClip plug, Restoring from service position, CombiClip

Contents

English Rider 15T Rider 15T AWD Rider 15Ts AWD Contents After the ﬁrst 8 hours Service journalPre-delivery service Introduction Symbols KEY to Symbols KEY to Symbols What is what on the ride-on mower What is WHAT? Safety instructions Safety InstructionsInsure your Rider General use This is what you do Driving on slopes Children Maintenance Transport Presentation Cutting unit Cutting height adjustment leverLifting lever for the cutting unit Lights Fuelling Exercise care and refuel outdoors see safety instructionsRelease lever Clutch control Rider 15T AWD and Rider 15Ts AWD Start the engine DrivingBefore starting Connecting the jump leads Starting the engine with a weak batteryDriving the Rider Remove the cables in the reverse order Stop the engine Cutting tips Maintenance schedule Maintenance Removing of the machine hoods CleaningChecking and adjusting the steering wires Can result in reduced braking ability Adjusting the parking brake Rider 15TChecking and adjusting of throttle wire Replacement of fuel ﬁlter Checking and adjusting the choke wireReplacing the air ﬁlter Cool before starting to replace the air ﬁlter Replacing the spark plug Checking the fuel pump’s air ﬁlterIgnition system Check the safety system Main fuse Replacing the light bulbsChecking the tyre pressure Checking the engine’s cooling air intake Fitting the cutting head When the engine is running. Mind your ﬁngersTrapping your hand Lift up the cutting unit Removing the cutting unit Hands when working with the blades Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Replacing the cutting unit belts Placing in the service position Service position for the cutting unit Checking the blades Restoring from service positionRemoving the BioClip plug CombiClip 103, CombiClip Checking the engine’s oil level LubricationChanging the oil ﬁlter Replacing the engine oil General lubrication Lubricating the belt adjusterChecking the transmission oil level Problem Procedure Troubleshooting schedule Storage ServiceWinter storage Guard Technical data Cutting unit CombiClip EN ISO 12100-2, EN-836 EC-declaration of conformity Applies to Europe onlyEC-declaration of conformity Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨