Fitting the cutting head, Trapping your hand | Husqvarna 15T AWD

Maintenance

Open the engine cover.

Check that the cooling intake is free from leaves, grass and dirt.

Check the air duct, located on the inside of the engine cover, ensure it is clean and does not rub against the cooling air intake.

A blocked cooling intake will interfere with the cooling of the engine, which can damage the engine.

WARNING! The cooling air intake rotates

!when the engine is running. Mind your ﬁngers.

Fitting the cutting head

WARNING! Wear protective glasses when

!ﬁtting the cutting unit. The spring which tensions up the belt may break and cause personal injury.

1Place the Rider on a ﬂat surface and apply the parking brake.

2Check that the lever for setting the cutting height is in the lowest position and that the lifting lever for the cutting unit is in mowing position.

3Push the equipment frame down and place the catch against the frame.

4 Engage the belt in the belt holder.

5Push the deck in and put the front guide plugs in the grooves on the equipment frame, one on each side.

	!	WARNING! Observe caution to avoid
		trapping your hand.

	6 Lift up the cutting unit

7Push the unit in so that the interior plugs touch the bottom of the equipment frame’s grooves.

8Fit the drive belt around the drive wheels of the cutting unit. Make sure the belt is placed on the correct side of the belt tensioner wheel.

English – 25

Image 25

Husqvarna 15T AWD, 15Ts AWD Fitting the cutting head, When the engine is running. Mind your ﬁngers, Trapping your hand

Contents

English Rider 15T Rider 15T AWD Rider 15Ts AWD Contents Pre-delivery service Service journalAfter the ﬁrst 8 hours Introduction Symbols KEY to Symbols KEY to Symbols What is what on the ride-on mower What is WHAT? Safety instructions Safety InstructionsInsure your Rider General use This is what you do Driving on slopes Children Maintenance Transport Presentation Cutting unit Cutting height adjustment leverLifting lever for the cutting unit Lights Fuelling Exercise care and refuel outdoors see safety instructionsRelease lever Clutch control Rider 15T AWD and Rider 15Ts AWD Before starting DrivingStart the engine Connecting the jump leads Starting the engine with a weak batteryDriving the Rider Remove the cables in the reverse order Stop the engine Cutting tips Maintenance schedule Maintenance Checking and adjusting the steering wires CleaningRemoving of the machine hoods Checking and adjusting of throttle wire Adjusting the parking brake Rider 15TCan result in reduced braking ability Replacement of fuel ﬁlter Checking and adjusting the choke wireReplacing the air ﬁlter Cool before starting to replace the air ﬁlter Ignition system Checking the fuel pump’s air ﬁlterReplacing the spark plug Check the safety system Main fuse Replacing the light bulbsChecking the tyre pressure Checking the engine’s cooling air intake Fitting the cutting head When the engine is running. Mind your ﬁngersTrapping your hand Lift up the cutting unit Removing the cutting unit Hands when working with the blades Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Replacing the cutting unit belts Placing in the service position Service position for the cutting unit Checking the blades Restoring from service positionRemoving the BioClip plug CombiClip 103, CombiClip Checking the engine’s oil level LubricationChanging the oil ﬁlter Replacing the engine oil Checking the transmission oil level Lubricating the belt adjusterGeneral lubrication Problem Procedure Troubleshooting schedule Storage ServiceWinter storage Guard Technical data Cutting unit CombiClip EC-declaration of conformity EC-declaration of conformity Applies to Europe onlyEN ISO 12100-2, EN-836 Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨