SMC Networks SMC7800A/VCP manual System and Port Status LEDs

Page 23

SYSTEM AND PORT STATUS LEDS

System and Port Status LEDs

The CPE includes key system and port indications that simplify installation and network troubleshooting. The LEDs, which are located on the front panel for easy viewing, are described in the following table.

Table 2-1 System and Port Status LEDs

LED

Status

Description

System Status

Indicators

 

 

 

 

POWER

On

Power is being supplied to the CPE.

 

 

 

 

Off

No power is being supplied to the CPE.

 

 

 

DIAG*

On

A failure has been detected during bootup

 

 

(including self-test failure or other problem).

 

 

 

 

Off

CPE successfully passed bootup diagnostics.

 

 

 

 

Flashing

Diagnostics are in progress.

 

 

 

Port Status Indicators

 

 

 

 

SPEED

On

Ethernet port is operating at 100 Mbps.

 

 

 

 

Off

Ethernet port is operating at 10 Mbps.

 

 

 

DUPLEX

On

Ethernet port is operating at full duplex.

 

 

 

 

Off

Ethernet port is operating at half duplex.

 

 

 

VDSL*

On

VDSL port has a valid link with a VDSL switch.

 

 

 

 

Off

VDSL port has no link with a VDSL switch.

 

 

 

 

Flashing

VDSL port training connection to VDSL switch.

 

 

 

LAN

On

Ethernet port has a valid link with attached device.

 

 

 

 

Off

Ethernet port has no link with other device.

 

 

 

 

Flashing

CPE is transmitting or receiving data on this port.

 

 

 

* These LEDs also turn on when firmware is being updated.

2-3

Image 23
Contents TigerAccess EE Page TigerAccess-EE CPE Installation Guide Trademarks Limited Warranty SMC Networks, Inc Mason Irvine, CA FCC Part CompliancesFCC Class B Industry Canada Class B CE Mark Declaration of Conformance for EMI and Safety EECLVD End of Product Life Span Environmental StatementDocumentation PurposeAudience Manufacturing MaterialsViii Table of Contents Glossary Index Overview Chapter AboutAbout the TIGERACCESS-EE CPE Vdsl Technology Providing Broadband Internet Access through VdslMaximum Rates and Distances Features and BenefitsSystem Requirements About the TIGERACCESS-EE CPE Unpacking Hardware DescriptionFront and Rear Panels Front and Rear PanelSystem and Port Status LEDs System and Port Status LEDsHardware Description Cable Connections Chapter InstallationInstallation Overview Powering On Windows Configuring the TCP/IP ProtocolsWindows 95/98/NT Mac OS Windows XPTable A-1 Troubleshooting Chart Appendix a TroubleshootingDiagnosing CPE Indicators Vdsl If You Cannot Connect to the InternetTwisted-Pair Cable and Pin Assignments Appendix B CablesTable B-1 10/100BASE-TX MDI and MDI-X Port Pinouts 10BASE-T/100BASE-TX Pin AssignmentsFigure B-2 Straight-through Wiring Straight-Through WiringCable Testing for Existing Category 5 Cable Crossover WiringRJ-11 Ports Figure B-4 RJ-11 WiringPin Table B-2 RJ-11 Port PinoutsVdsl Functional Criteria Appendix C SpecificationsPhysical Characteristics Standards Immunity SafetyCompliances CE Mark EmissionsSpecifications Glossary LAN Segment EthernetFast Ethernet Full DuplexLocal Area Network LAN Media Access Control MACPlain Old Telephone Service Pots RJ-45 ConnectorVery high data rate Digital Subscriber Line 2 VDSL2 Transmission Control Protocol/Internet Protocol TCP/IPUser Datagram Protocol UDP Very high data rate Digital Subscriber Line VdslNumerics IndexIndex-2 Page For Technical SUPPORT, Call