SMC Networks 10G manual Installing the Switch, Selecting a Site

Page 39

CHAPTER 3 INSTALLING THE SWITCH

Selecting a Site

TigerStack 10G units can be mounted in a standard 19-inch equipment rack or on a flat surface. Be sure to follow the guidelines below when choosing a location.

◆The site should:

•be at the center of all the devices you want to link and near a power outlet.

•be able to maintain its temperature within 0 to 50 °C (32 to

122 °F) and its humidity within 5% to 95%, non-condensing

•provide adequate space (approximately two inches) on all sides for proper air flow

•be accessible for installing, cabling and maintaining the devices

•allow the status LEDs to be clearly visible

◆Make sure twisted-pair cable is always routed away from power lines, fluorescent lighting fixtures and other sources of electrical interference, such as radios and transmitters.

◆Make sure that a separate grounded power outlet that provides 100 to 240 VAC, 50 to 60 Hz, is within 2.44 m (8 feet) of each device and is powered from an independent circuit breaker. As with any equipment, using a filter or surge suppressor is recommended.

3-1

Image 39

Contents TigerStack 10G Page TigerStack 10G Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Japan Vcci Class a CompliancesFCC Class a Industry Canada Class aCE Mark Declaration of Conformance for EMI and Safety EEC Safety Compliance Taiwan Bsmi Class a Australia AS/NZS 3548 1995 Class aWarnhinweis Faseroptikanschlüsse Optische Sicherheit France and Peru only Power Cord SafetyVii Viii Documentation Environmental StatementEnd of Product Life Span Manufacturing MaterialsRelated Publications PurposeTable of Contents Making Network Connections Appendices Xiv Tables Xvi Figures Xviii Overview Chapter About Tigerstack 10GSMC8748M and SMC8724M Front Panels Switch ArchitectureDescription of Hardware Management Options10/100/1000BASE-T Ports Stacking Ports SFP SlotsPort LEDs Port Status LEDs Status LEDsSystem Status LEDs System Status LEDs Connectivity Features and BenefitsOptional Redundant Power Unit Power Supply ReceptaclesExpandability PerformanceManagement About the Tigerstack 10G Chapter Network Planning Introduction to SwitchingCollapsed Backbone Application ExamplesNetwork Aggregation Plan Network Aggregation PlanRemote Connection with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Selecting a Site Installing the SwitchRJ-45 Connections Ethernet CablingEquipment Checklist Package ContentsOptional Rack-Mounting Equipment Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingInserting an SFP Transceiver into a Slot Installing an Optional SFP Transceiver into the SwitchMaking Stacking Connections Connecting Switches in a StackStacking Topologies Power Receptacle Connecting to a Power SourceSerial Port DB-9 DTE Pin-Out Connecting to the Console PortInstalling the Switch Cabling Guidelines Connecting Network DevicesChapter Making Network Connections Twisted-Pair DevicesMaking Twisted-Pair Connections Connecting to PCs, Servers, Hubs and SwitchesWiring Closet Connections Network Wiring ConnectionsFiber Optic SFP Devices Making LC Port Connections Maximum 1000BASE-T Gigabit Ethernet Cable Length Connectivity Rules1000BASE-T Cable Requirements Mbps Gigabit Ethernet Collision LengthMbps Ethernet Collision Domain Mbps Fast Ethernet Collision DomainCable Labeling and Connection Records Appendix a Troubleshooting Diagnosing Switch IndicatorsTable A-1 Troubleshooting Chart Installation Power and Cooling ProblemsStack Troubleshooting In-Band AccessTroubleshooting Twisted-Pair Cable and Pin Assignments Appendix B CablesStraight-Through Wiring 10BASE-T/100BASE-TX Pin AssignmentsTable B-1 10/100BASE-TX MDI and MDI-X Port Pinouts Figure B-2 Straight-through Wiring Crossover WiringTable B-2 1000BASE-T MDI-X and MDI Port Pinouts 1000BASE-T Pin AssignmentsAdjusting Existing Category 5 Cabling to Run 1000BASE-T Cable Testing for Existing Category 5 CableFiber Standards Physical Characteristics Appendix C SpecificationsPower Consumption WeightTemperature Power SupplySwitch Features Management FeaturesStandards CE Mark Emissions WarrantySafety CompliancesAppendix D Ordering Information Ordering Information Glossary 1000BASE-TAuto-Negotiation End Station BandwidthCollision Collision DomainIeee 802.3ab Gigabit EthernetFull Duplex IeeeSwitched Ports Media Access Control MACRedundant Power Unit RPU RJ-45 ConnectorVirtual LAN Vlan Transmission Control Protocol/Internet Protocol TCP/IPGlossary-6 Numerics IndexIndex-2 Index-3 Index-4 Page For Technical SUPPORT, Call