Seagate ST3160310CS, ST3320310CS manual Configuring the drive, Serial ATA cables and connectors

Page 26

3.2Configuring the drive

Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationship. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. Both drives behave as if they are Device 0 (master) devices.

Serial ATA drives are designed for easy installation. It is usually not necessary to set any jumpers on the drive for proper operation; however, if you connect the drive and receive a “drive not detected” error, your SATA- equipped motherboard or host adapter may use a chipset that does not support SATA speed autonegotiation. If you have a motherboard or host adapter that does not support autonegotiation:

•Install a jumper as shown in Figure 2 below to limit the data transfer rate to 1.5 Gbits per second (and leave the drive connected to the SATA-equipped motherboard or host adapter that doesn’t support autonegotiation) or

•Install a SATA host adapter that supports autonegotiation, leave the drive jumper block set to “Normal operation” (see Figure 2 below), and connect the drive to that adapter. This option has the benefit of not limiting the drive to a 1.5 Gbits/sec transfer rate.

3.0 Gbits per second operation

Limit data transfer rate to 1.5 Gbits per second

Jumper block

SATA power connector

SATA interface connector

Figure 2. Serial ATA connectors

3.3Serial ATA cables and connectors

The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connec- tions. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 6 for connector pin definitions. Either end of the SATA signal cable can be attached to the drive or host.

For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind mateable.

For installations which require cables, you can connect the drive as illustrated in Figure 3.

Signal connector

Power connector

Signal cable

Power cable

Figure 3. Attaching SATA cabling

Each cable is keyed to ensure correct orientation. Pipeline HD Series SATA drives support latching SATA con- nectors.

20

Pipeline HD Series SATA Product Manual, Rev. C

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Pipeline HD Series Sata ST3500321CS ST3500422CS ST3320310CS ST3320410CS ST3160310CSRevision history Revision Date Sheets affected or commentsContents Pipeline HD Series Sata Product Manual, Rev. C List of Figures Page Introduction About the Serial ATA interface Drive specifications Specification summary tablesDrive specifications summary for 500 Gbyte models Drive specification ST3500422CS ST3500321CSPipeline HD Series Sata Product Manual, Rev. C Drive specifications summary for 320 and 160 Gbyte models Drive specification ST3320410CS ST3320310CS ST3160310CSPipeline HD Series Sata Product Manual, Rev. C Formatted capacity Default logical geometryLBA mode Recording and interface technologyStart/stop times Physical characteristicsSeek time Power specifications Voltage tolerance Typical current profilesConducted noise Idle mode Power-management modesActive mode Sleep modeEnvironmental specifications Nonoperating shock GB models ShockOperating shock 160 GB modelsElectromagnetic immunity Drive A-weighted Sound Power Levels SWL, BAAcoustics emissions Test for Prominent Discrete Tones PDTsAgency certification Safety certificationReliability Annualized Failure Rate AFRFCC verification Korean RRLAustralian C-Tick N176 Environmental protection Corrosive environmentConfiguring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions for 500 GB models Drive mountingMounting dimensions for 320 and 160 GB models Serial ATA Sata interface Hot-Plug compatibilitySignal Serial ATA device plug connector pin definitionsSerial ATA connector pin definitions Pin Function DefinitionCommand name Command code in hex Supported ATA commandsSupported ATA commands F4H Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Bit WordWord Set Features command Set Features command valuesCode in features register A.R.T. command 3 S.M.A.R.T. commandsA.R.T. commands Presales Support Seagate Technology support servicesInternet Technical SupportData Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index ITE Page Pipeline HD Series Sata Product Manual, Rev. C Page Seagate Technology LLC

ST3320310CS, ST3500321CS, ST3320410CS, ST3160310CS, ST3500422CS specifications

Seagate has long been recognized as a leader in data storage solutions, and their range of hard drives continues to reflect innovation and reliability. Among the notable SATA drives are the Seagate ST3500422CS, ST3160310CS, ST3320410CS, ST3500321CS, and ST3320310CS models, all designed for various consumer and enterprise applications.

The ST3500422CS operates at a capacity of 500GB, combining high performance with energy efficiency. With a spindle speed of 7200 RPM and a 32MB cache, it ensures rapid data access and transfer rates, making it suitable for multimedia storage and gaming applications. This drive incorporates Seagate’s Instant Secure Erase technology, which allows users to securely wipe their data quickly, ensuring privacy and data protection.

Next, the ST3160310CS model offers a storage capacity of 160GB, ideal for smaller applications requiring faster access times. Also spinning at 7200 RPM, it features a similar 8MB cache, ensuring good performance for everyday computing needs. Its compact design makes it suitable for both desktop systems and where space is at a premium.

The ST3320410CS is designed for larger capacity requirements, providing up to 320GB of storage space. This drive features enhanced data integrity with a 16MB cache and a consistent performance level that makes it suitable for both personal computing and lightweight server applications. Its Balancing Act technology optimizes the drive's performance across multiple workloads, extending its lifespan.

The ST3500321CS provides users with 500GB of storage, similar to the ST3500422CS but with a focus on data reliability. Featuring advanced error correction technologies, it diminishes the chance of data loss, making it a great choice for critical applications requiring consistent reliability.

Finally, the ST3320310CS model holds 320GB of storage capacity and shares many characteristics with its counterparts, such as the 7200 RPM speed and strong error correction mechanisms. The drive also utilizes Seagate's Thermal Fly-Height Control technology, which further enhances reliability by adjusting the read/write heads according to the drive's operational temperature.

Overall, these drives exemplify Seagate's commitment to performance, efficiency, and data protection across their various storage solutions. With a range of capacities and features, they cater to diverse user needs while ensuring reliability and speed in data access.
Top Page Image Contents