Seagate ST1000NM0033 manual Handling and STATIC-DISCHARGE Precautions, Configuring the Drive

Page 30

3.0CONFIGURING AND MOUNTING THE DRIVE

This section contains the specifications and instructions for configuring and mounting the drive.

3.1HANDLING AND STATIC-DISCHARGE PRECAUTIONS

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

CAUTION

•Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.

•Handle the drive by its edges or frame only.

•The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.

•Always rest the drive on a padded, antistatic surface until you mount it in the computer.

•Do not touch the connector pins or the printed circuit board.

•Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.

3.2CONFIGURING THE DRIVE

Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationship. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. Both drives behave as if they are Device 0 (master) devices.

3.3SERIAL ATA CABLES AND CONNECTORS

The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 in). See Table 8 for connector pin definitions. Either end of the SATA signal cable can be attached to the drive or host.

For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind mateable.

For installations which require cables, you can connect the drive as illustrated in Figure 10.

Signal connector

Power connector

Signal cable

Power cable

Figure 10. Attaching SATA cabling

Each cable is keyed to ensure correct orientation. Constellation ES.3 Serial ATA drives support latching SATA connectors.

26

CONSTELLATION ES.3 SERIAL ATA PRODUCT MANUAL, REV. A

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Constellation ES.3 Serial ATA Document Revision History Contents Serial ATA Sata interface Seagate Technology Support Services Constellation ES.3 Serial ATA Product Manual, Rev. a Introduction About the Serial ATA Interface Drive Specifications Specification Summary TablesDrive specification Formatted Capacity LBA modeDefault Logical Geometry Recording and Interface TechnologyPower Specifications 4TB Drive DC power requirements Peak operating current sequential write3TB Drive DC power requirements 2TB Drive DC power requirements 1TB Drive DC power requirements Typical current profiles TB Typical 5V startup and operation current profileTypical current profiles Typical current profiles Typical current profiles Idle mode Power-management modesActive mode Sleep modeExtended Power Conditions PowerChoiceTM PowerChoice is invoked using one of two methodsPowerChoice Manufacture Default Power Condition Timer Values PowerChoice Supported Extended Power Condition IndentifiersEnvironmental Limits Acoustics Test for Prominent Discrete Tones PdtsElectromagnetic Immunity ReliabilityRadio frequency environments Agency Certification Corrosive Environment Environmental ProtectionChina Restriction of Hazardous Substances RoHS Directive Reference DocumentsStorage Product WarrantyShipping Product repair and return informationHandling and STATIC-DISCHARGE Precautions Configuring the DriveSerial ATA Cables and Connectors Drive Mounting Mechanical specifications Mounting dimensions-top, side and end viewPurpose Seagate Enterprise SEDsLevel 2 security Random Number Generator RNG Controlled AccessData Encryption Drive LockingSupported Commands Authenticated Firmware DownloadPower Requirements Data BandsATA Security Erase Unit Command on SED Sata Drives RevertspSerial ATA Device Plug Connector PIN Definitions Serial ATA connector pin definitionsHOT-PLUG Compatibility Supported ATA Commands Supported ATA commandsF6H Identify Device command CEHXxxx H Description if bit is set to BIT Word Set Features command Set Features command values3 S.M.A.R.T. commands M.A.R.T. commandsConstellation ES.3 Serial ATA Product MANUAL, REV. a Index Constellation ES.3 Serial ATA Product MANUAL, REV. a Index Constellation ES.3 Serial ATA Product MANUAL, REV. a Page Seagate Technology LLC
Related manuals
Manual 76 pages 29.86 Kb

ST1000NM0033 specifications

The Seagate ST1000NM0033 is a high-performance hard disk drive (HDD) designed specifically for enterprise applications. With a storage capacity of 1TB, it offers a balance of performance, reliability, and efficiency, making it suitable for data centers, cloud storage, and server environments. Built with Seagate's robust engineering, the ST1000NM0033 is ideal for handling heavy workloads and intensive data processes.

One of the standout features of this HDD is its rotational speed of 7200 RPM. This speed allows for quick data access and fast read/write operations, which is essential for data-intensive applications. The drive is equipped with 64MB of cache, further enhancing its efficiency by speeding up data retrieval for frequently accessed files.

Another key characteristic of the ST1000NM0033 is its SATA interface, which typically facilitates high-bandwidth data transfer rates. With a sustained data transfer rate of up to 160 MB/s, it ensures that large files, such as videos and databases, can be transferred swiftly, minimizing downtime and improving overall system performance.

The drive's durability is backed by Seagate’s Advanced Format technology, which enhances the format compatibility, storage efficiency, and reliability of the drive through improved error correction. With a mean time between failures (MTBF) rating of 1 million hours, users can trust the STA0033 to provide exceptional longevity and stability, critical in enterprise environments where data integrity is paramount.

Furthermore, the ST1000NM0033 supports various workload types due to its design optimized for multi-user environments. The drive can handle up to 180TB/year workload rate, making it capable of supporting applications with high data demand.

Environmentally, Seagate ensures that this model is energy efficient, contributing to reduced power consumption in enterprise settings. The drive operates effectively within a specified temperature range, ensuring that it remains operational under different environmental conditions.

In summary, the Seagate ST1000NM0033 is an excellent choice for businesses seeking a reliable, high-capacity HDD with robust performance features. Its combination of speed, efficiency, durability, and capacity positions it as a strong contender in the enterprise storage solutions market. With its extensive feature set, it continues to cater to the demanding needs of modern data centers and enterprise applications.
Top Page Image Contents