Seagate ST2000VM002, ST1500VM002 Supported ATA commands, Command name Command code in hex, E5H

Page 30

Serial ATA Interface

www.seagate.com

Table 5 Serial ATA connector pin definitions (Continued)

Segment	Pin	Function	Definition

	P1	V33	3.3V power
	P2	V33	3.3V power
	P3	V33	3.3V power, pre-charge, 2nd mate
	P4	Ground	1st mate

	P5	Ground	2nd mate

	P6	Ground	2nd mate

	P7	V5	5V power, pre-charge, 2nd mate

Power	P8	V5	5V power

	P9	V5	5V power
	P10	Ground	2nd mate

	P11	Ground or LED signal	If grounded, drive does not use deferred spin

	P12	Ground	1st mate.

	P13	V12	12V power, pre-charge, 2nd mate
	P14	V12	12V power
	P15	V12	12V power

Notes:

1.All pins are in a single row, with a 1.27mm (0.050”) pitch.

2.The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are:

•the ground pins P4 and P12.

•the pre-charge power pins and the other ground pins.

•the signal pins and the rest of the power pins.

3.There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration.

4.All used voltage pins (Vx) must be terminated.

4.3Supported ATA commands

The following table lists Serial ATA standard commands that the drive supports.

For a detailed description of the ATA commands, refer to the Serial ATA International Organization: Serial ATA Revision 3.0 (http://www.sata-io.org).

See “S.M.A.R.T. commands” on page 38.for details and subcommands used in the S.M.A.R.T. implementation.

Table 6 Supported ATA commands

Command name	Command code (in hex)

Check Power Mode	E5H
Configure Stream	51H
Device Configuration Freeze Lock	B1H / C1H

30	Pipeline HD SATA Product Manual, Rev. B

Image 30

Contents Pipeline HD 100633414 Rev. B JanuaryDocument Revision History Revision Date Description of changesContents Pipeline HD Sata Product Manual, Rev. B Figures Pipeline HD Sata Product Manual, Rev. B Seagate Technology Support Services Pipeline HD Sata Product Manual, Rev. B Introduction About the Serial ATA InterfaceIntroduction Specification summary tables Drive specification ST2000VM002 ST1500VM002Drive Specifications Formatted capacity LBA modeDefault logical geometry Recording and interface technologyPower consumption Physical characteristicsPower specifications Seek timeSpinup Idle* † 151 303 Operating 374 256 Standby 085 Sleep Typical Current Profiles Conducted noise Power-management modesPower modes Heads Spindle Buffer Voltage toleranceHumidity Environmental specifications Drive case temperatureTemperature gradient AltitudeOperating vibration Vibration2000GB and 1500GB models Nonoperating vibrationElectromagnetic immunity AcousticsTest for Prominent Discrete Tones PDTs Idle Seek All modelsElectromagnetic compatibility WarrantyAgency certification Safety certification FCC verificationEnvironmental protection China Restriction of Hazardous Substances RoHS DirectiveCorrosive environment Drive Specifications Handling and static-discharge precautions Configuring the driveSerial ATA cables and connectors Drive mounting Attaching Sata cabling Mounting dimensions 2000 and 1500GB models Configuring and Mounting the Drive Ground 2nd mate Differential signal pair a from PHY Ground 2nd mate Differential signal pair B from PHYSegment Pin Function Definition Supported ATA commands Command name Command code in hexE5H ECH E7HEAH E3HF5H F3HF4H F1HIdentify Device command Word Description Value57-58 Current capacity in sectors Number of current logical headsNumber of current logical sectors per logical track Number of sectors transferred during a Read MultipleFffeh Hardware reset valueBE01H 160-254 ATA-reserved 0000H 255 Integrity word XxA5HBit Word Set Features command A.R.T. commands Code in features register A.R.T. commandIndex EprmlPipeline HD Sata Product Manual, Rev. B Pipeline HD Sata Product Manual, Rev. B Pipeline HD Sata Product Manual, Rev. B Page Seagate Technology LLC