Seagate ST1500VM002, ST2000VM002 Handling and static-discharge precautions, Configuring the drive

Page 25

3.0 Configuring and Mounting the Drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1Handling and static-discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

•Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.

•Handle the drive by its edges or frame only.

•The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.

•Always rest the drive on a padded, antistatic surface until you mount it in the computer.

•Do not touch the connector pins or the printed circuit board.

•Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.

3.2Configuring the drive

Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationship. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. Both drives behave as if they are Device 0 (master) devices.

Serial ATA drives are designed for easy installation. It is usually not necessary to set any jumpers on the drive for proper operation; however, if you connect the drive and receive a “drive not detected” error, your SATA-equipped motherboard or host adapter may use a chipset that does not support SATA speed autonegotiation.

3.3Serial ATA cables and connectors

The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 in). See Table 5 for connector pin definitions. Either end of the SATA signal cable can be attached to the drive or host.

For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind mateable.

For installations which require cables, you can connect the drive as illustrated in Figure 3.

Pipeline HD SATA Product Manual, Rev. B

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 100633414 Rev. B January Pipeline HDRevision Date Description of changes Document Revision HistoryContents Pipeline HD Sata Product Manual, Rev. B Figures Pipeline HD Sata Product Manual, Rev. B Seagate Technology Support Services Pipeline HD Sata Product Manual, Rev. B About the Serial ATA Interface IntroductionIntroduction Drive specification ST2000VM002 ST1500VM002 Specification summary tablesDrive Specifications Default logical geometry LBA modeFormatted capacity Recording and interface technologyPower specifications Physical characteristicsPower consumption Seek timeSpinup Idle* † 151 303 Operating 374 256 Standby 085 Sleep Typical Current Profiles Power modes Heads Spindle Buffer Power-management modesConducted noise Voltage toleranceTemperature gradient Environmental specifications Drive case temperatureHumidity Altitude2000GB and 1500GB models VibrationOperating vibration Nonoperating vibrationTest for Prominent Discrete Tones PDTs AcousticsElectromagnetic immunity Idle Seek All modelsAgency certification Safety certification WarrantyElectromagnetic compatibility FCC verificationChina Restriction of Hazardous Substances RoHS Directive Environmental protectionCorrosive environment Drive Specifications Configuring the drive Handling and static-discharge precautionsSerial ATA cables and connectors Attaching Sata cabling Drive mountingMounting dimensions 2000 and 1500GB models Configuring and Mounting the Drive Ground 2nd mate Differential signal pair B from PHY Ground 2nd mate Differential signal pair a from PHYSegment Pin Function Definition Command name Command code in hex Supported ATA commandsE5H EAH E7HECH E3HF4H F3HF5H F1HWord Description Value Identify Device commandNumber of current logical sectors per logical track Number of current logical heads57-58 Current capacity in sectors Number of sectors transferred during a Read MultipleBE01H Hardware reset valueFffeh 160-254 ATA-reserved 0000H 255 Integrity word XxA5HBit Word Set Features command Code in features register A.R.T. command A.R.T. commandsEprml IndexPipeline HD Sata Product Manual, Rev. B Pipeline HD Sata Product Manual, Rev. B Pipeline HD Sata Product Manual, Rev. B Page Seagate Technology LLC

ST2000VM002, ST1500VM002 specifications

The Seagate ST1500VM002 and ST2000VM002 are part of the Seagate Video 3.5 Series, designed specifically for surveillance systems and DVRs. These hard drives provide robust storage solutions tailored to handle the high demands of continuous video recording and playback.

Both models boast a 3.5-inch form factor and utilize SATA III interfaces, ensuring fast data transfer rates essential for processing large video files from multiple security cameras. The ST1500VM002 offers a storage capacity of 1.5TB, while the ST2000VM002 provides an enhanced capacity of 2TB, making them suitable for extensive surveillance setups that may require longer retention of video content.

One of the most significant features of these drives is their support for 24/7 operation, allowing them to perform reliably and efficiently under constant load. This aspect is particularly important for security applications where data is consistently being recorded and accessed without downtime. Moreover, both models are optimized for high workload rates, capable of handling workloads of up to 180TB per year, which is essential for the rigorous demands of surveillance use.

The Seagate ST1500VM002 and ST2000VM002 also feature advanced technologies that help enhance performance and reliability. These drives incorporate AgileArray technology, which optimizes drive performance in multi-drive systems and improves RAID performance. This technology also features error recovery controls, which are critical for maintaining data integrity over time.

In terms of reliability, both drives are built with robust components designed to withstand the harsh conditions typically associated with surveillance environments. They come equipped with high shock resistance, ensuring they remain functional in various conditions, preserving valuable data even in the event of physical impacts or vibrations.

Furthermore, they include features like Seagate Rescue Data Recovery Services, providing customers peace of mind knowing that their data can be recovered in unexpected scenarios. Overall, the Seagate ST1500VM002 and ST2000VM002 are excellent choices for anyone in need of high-capacity, reliable storage solutions for their surveillance needs, offering a blend of advanced technology, robust performance, and dependable data integrity.
Top Page Image Contents