Seagate ST3640330AS Acoustics, Electromagnetic immunity, Test for Prominent Discrete Tones PDTs

Page 23

2.9Acoustics

Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea- surements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward.

Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation:

(Number of seeks per second = 0.4 / (average latency + average access time)

Table 5:

Fluid Dynamic Bearing (FDB) motor acoustics

 

 

 

 

 

 

 

 

Idle*

Performance Seek

Quiet Seek

 

 

 

 

ST31000340AS, ST31000640AS,

2.9 bels (typ)

3.2 bels (typ)

3.1 bels (typ)

ST3750330AS, ST3750630AS,

3.1 bels (max)

3.3 bels (max)

3.2 bels (max)

ST3640330AS and ST3640630AS

 

 

 

 

 

 

 

ST3500320AS, ST3500620AS and

2.7 bels (typ)

3.1 bels (typ)

3.0 bels (typ)

ST3500820AS

2.9 bels (max)

3.2 bels (max)

3.1 bels (max)

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

2.9.1Test for Prominent Discrete Tones (PDTs)

Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses this threshold curve (originated in ISO 389-7) to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards.

2.10Electromagnetic immunity

When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environments defined in the following table:

Table 6:

Radio frequency environments

 

 

 

 

 

 

 

Test

 

Description

Performance level

Reference standard

 

 

 

 

 

Electrostatic

 

Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV

B

EN 61000-4-2: 95

discharge

 

 

 

 

Radiated RF

 

80 to 1,000 MHz, 3 V/m,

A

EN 61000-4-3: 96

immunity

 

80% AM with 1 kHz sine

 

ENV 50204: 95

 

 

900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz

 

 

Electrical fast

± 1 kV on AC mains, ± 0.5 kV on external I/O

B

EN 61000-4-4: 95

transient

 

 

 

 

Surge immunity

± 1 kV differential, ± 2 kV common, AC mains

B

EN 61000-4-5: 95

 

 

 

 

Conducted RF

150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz sine

A

EN 61000-4-6: 97

immunity

 

 

 

 

Voltage dips,

 

0% open, 5 seconds

C

EN 61000-4-11: 94

interrupts

 

0% short, 5 seconds

C

 

 

 

40%, 0.10 seconds

C

 

 

 

70%, 0.01 seconds

B

 

Barracuda 7200.11 Serial ATA Product Manual, Rev. G

17

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Barracuda 7200.11 Serial ATA Revision Date Sheets affected or comments Revision historyContents Barracuda 7200.11 Serial ATA Product Manual, Rev. G Typical 5V startup and operation current profile List of FiguresPage Introduction About the Serial ATA interface Drive specifications Drive specifications summary for 1000 and 750 Gbyte models Barracuda 7200.11 Serial ATA Product Manual, Rev. G Drive specifications summary for 640 Gbyte models Will display the warranty information for your drive Drive specifications summary for 500 Gbyte models Barracuda 7200.11 Serial ATA Product Manual, Rev. G Recording and interface technology Default logical geometryLBA mode Formatted capacityTypical seek times msec Read Write Physical characteristicsSeek time Start/stop timesPower specifications Typical 12V startup and operation current profile Typical 5V startup and operation current profileSleep mode Power-management modesActive mode Idle modeEnvironmental specifications 1000 GB, 750 GB and 500 GB models VibrationOperating vibration Nonoperating vibrationTest for Prominent Discrete Tones PDTs AcousticsElectromagnetic immunity Fluid Dynamic Bearing FDB motor acousticsElectromagnetic compatibility Safety certificationReliability Agency certificationFCC verification Korean RRLAustralian C-Tick N176 Corrosive environment Environmental protection383  Handling and static-discharge precautions Configuring and mounting the driveSerial ATA cables and connectors Configuring the driveDrive mounting Mounting dimensionsBarracuda 7200.11 Serial ATA Product Manual, Rev. G Hot-Plug compatibility Serial ATA Sata interfacePin Function Definition Serial ATA device plug connector pin definitionsSerial ATA connector pin definitions SignalCommand name Command code in hex Supported ATA commandsSupported ATA commands F4H Word Description Value Identify Device commandXx07H Bit Word Description if bit is set to Bit WordWord Set Features command values Set Features commandCode in features register A.R.T. command 3 S.M.A.R.T. commandsM.A.R.T. commands Technical Support Seagate Technology support servicesPresales Support Data Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index ITE Page Barracuda 7200.11 Serial ATA Product Manual, Rev. G Page Disc Drive, Scotts Valley, California 95066-4544, USA
Related manuals
Manual 46 pages 42.51 Kb

ST3640630AS, ST3500820AS, ST3500320AS, ST3500620AS, ST31000640AS specifications

Seagate has long been a prominent player in the hard drive industry, and its line of SATA drives, including the ST3640330AS, ST3750330AS, ST3750630AS, ST31000340AS, and ST31000640AS, showcases a blend of performance, reliability, and advanced technology. These drives cater to various user needs, from consumer desktops to enterprise applications.

The ST3640330AS and ST3750330AS models are designed with a 7200 RPM spinning speed, ensuring fast data throughput for gaming, multimedia, and everyday computing tasks. With a SATA interface and compatibility with the latest systems, these drives are ideal for users seeking efficient storage solutions. The ST3640330AS provides 640 GB of storage, while the ST3750330AS boasts a generous 750 GB capacity, offering ample space for large files and applications.

Moving to the ST3750630AS, this model continues the trend of high performance, offering 750 GB of storage but enhanced with Seagate’s advanced error-correcting technology. It also features an updated cache architecture that optimizes read and write speeds while minimizing latency. This drive is particularly beneficial for users who require reliable backups and quick access to data.

The ST31000340AS and ST31000640AS are both part of Seagate’s 1 TB series and are engineered for durability and longevity. The ST31000340AS features traditional SATA technology, providing users with a balance between cost and performance. On the other hand, the ST31000640AS integrates improved power management features that result in lower energy consumption without compromising performance. This makes it a suitable choice for environmentally-conscious consumers or businesses looking to reduce operational costs.

All models feature Seagate's proprietary technologies such as SoftSonic drives, which result in quieter operation, and advanced power management capabilities that extend the lifespan of the hard drives. They are equipped with robust error recovery and data security features, ensuring data integrity and protecting against data loss.

Overall, the Seagate ST3640330AS, ST3750330AS, ST3750630AS, ST31000340AS, and ST31000640AS drives represent a comprehensive range of storage solutions that combine capacity, speed, and cost-effectiveness, making them a popular choice for a variety of users, from casual consumers to demanding enterprise environments.
Top Page Image Contents