Seagate 7200.11 manual Drive mounting, Mounting dimensions 1000 & 640 GB models

Page 27

3.4Drive mounting

You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 3 for drive mounting dimensions. Follow these important mounting precau- tions when mounting the drive:

•Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.

•Use only 6-32 UNC mounting screws.

•The screws should be inserted no more than 0.150 inch (3.81 mm) into the bottom or side mounting holes.

•Do not overtighten the mounting screws (maximum torque: 6 inch-lb).

[1]

5.787 (146.9898) max.

Recommended case temperature measurement location

		1.122						1.638
		1.122				(41.605)			[1]
	+ .020					(41.605)			[1]
	+ .020
	(28.499
	(28.499

+.508)

[1][1]

4.000

(101.6)

.250 + .015 (6.35 + .381) (3x both sides)

4.000

(101.60)

.138

(3.505)

.814

(20.676)

C of conn. Datum B

L

2.00

(50.80)

C of drive

L

[1]

2 x 3.750

(2 x 95.25)

1.028 max [1]

(26.111 max)

Notes:

Dimensions are shown in inches (mm).

[1] Dimensions per SFF-8301 specification

2 x 1.625

(2 x 41.28) [1]

2 x 1.750 [1] (2 x 44.45)

4.000

(101.6)

[1]

Recommended case temperature measurement location

Figure 3. Mounting dimensions (1000 & 640 GB models)

Barracuda 7200.11 Serial ATA Product Manual, Rev. B

21

Image 27

Contents Barracuda 7200.11 Serial ATA Revision Date Sheets affected or comments Revision historyContents Barracuda 7200.11 Serial ATA Product Manual, Rev. B List of Figures Page Introduction About the Serial ATA interface Drive specifications Drive specifications summary for 1000 and 640 Gbyte models Will display the warranty information for your drive Drive specifications summary for 320 and 160 Gbyte models Barracuda 7200.11 Serial ATA Product Manual, Rev. B Recording and interface technology Default logical geometryLBA mode Formatted capacityPhysical characteristics Seek timeTypical seek times msec Read Write Start/stop times Power specificationsDC power requirements Conducted noiseVoltage tolerance Sleep mode Power-management modesActive mode Idle modeEnvironmental specifications Operating vibration Nonoperating shock 1000 & 640 GB models320 & 160 GB models VibrationTest for Prominent Discrete Tones PDTs AcousticsElectromagnetic immunity Fluid Dynamic Bearing FDB motor acousticsElectromagnetic compatibility Safety certificationReliability Agency certificationKorean RRL Australian C-Tick N176FCC verification Environmental protection Corrosive environmentChina Restriction of Hazardous Substances RoHS Directive Handling and static-discharge precautions Configuring and mounting the driveSerial ATA cables and connectors Configuring the driveDrive mounting Mounting dimensions 1000 & 640 GB modelsMounting dimensions 320 & 160 GB models Hot-Plug compatibility Serial ATA Sata interfacePin Function Definition Serial ATA device plug connector pin definitionsSerial ATA connector pin definitions SignalSupported ATA commands Supported ATA commandsCommand name Command code in hex F4H Word Description Value Identify Device commandXx07H Bit Word Description if bit is set to Bit WordWord Set Features command values Set Features command3 S.M.A.R.T. commands M.A.R.T. commandsCode in features register A.R.T. command Technical Support Seagate Technology support servicesInternet Presales SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index ITE Page Barracuda 7200.11 Serial ATA Product Manual, Rev. B Page Disc Drive, Scotts Valley, California 95066-4544, USA