Seagate ST3200827ACE, ST3120213ACE manual Physical characteristics, Seek time, Start/stop times

Page 18

2.5Physical characteristics

	Drive specification

	Maximum height
	(mm)	26.1
	(inches)	1.028

	Maximum width
	(mm)	101.6
	(inches)	101.6
	(inches)	4.000 ± 0.010
		4.000 ± 0.010

	Maximum length
	(mm)	146.99
	(inches)	5.787

	Typical weight
	ST3500841ACE	710 grams (1.57 lbs)
	ST3400833ACE
	ST3300822ACE	655 grams (1.44 lbs)
	ST3250824ACE	580 grams (1.28 lbs)
	ST3200827ACE
	ST3160212ACE
	ST3120213ACE
	ST3802110ACE

2.6Seek time

Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows:

•Track-to-track seek time is an average of all possible single-track seeks in both directions.

•Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead.

Typical seek times (msec)	Read	Write

Track-to-track	0.8	1.0

Average	18	20

Average latency:	4.16	4.16

Note. These drives are designed to consistently meet the seek times represented in this manual. Physical seeks, regardless of mode (such as track-to-track and average), are expected to meet or exceed the noted values. However, due to the manner in which these drives are formatted, benchmark tests that include command overhead or measure logical seeks may produce results that vary from these specifications.

2.7Start/stop times

Power-on to Ready (sec)	16

Standby to Ready (sec)	16 (max)

Ready to spindle stop (sec)	10 (max)

12	DB35 Series 7200.2 Product Manual, Rev. D

Image 18

Contents DB35 Series Page Contents DB35 Series 7200.2 Product Manual, Rev. D List of Figures DB35 Series 7200.2 Product Manual, Rev. D Introduction DB35 Series 7200.2 Product Manual, Rev. D Drive specifications Specification summary tableDrive specifications for 500 and 400 Gbyte models Drive specification ST3500841ACE ST3400833ACEFollowing web Drive specifications for 300, 250, and 200 Gbyte models Drive specification ST3300822ACE ST3250824ACE ST3200827ACEDB35 Series 7200.2 Product Manual, Rev. D Drive specifications for 160, 120, and 80 Gbyte models Drive specification ST3160212ACE ST3120213ACE ST3802110ACEAccess the following web Formatted capacity Default logical geometryLBA mode Recording and interface technologyDB35 Series 7200.2 Product Manual, Rev. D Physical characteristics Seek timeStart/stop times Power specifications Typical current profile Conducted noiseVoltage tolerance Idle mode Power-management modesActive mode Sleep modeEnvironmental specifications Vibration AcousticsNonoperating shock Operating vibrationElectromagnetic immunity ReliabilityRadio frequency environments Electromagnetic compatibility Safety certificationAgency certification Korean RRLEnvironmental protection FCC verificationEuropean Union Restriction of Hazardous Substances RoHS Corrosive environment DB35 Series 7200.2 Product Manual, Rev. D Configuring and mounting the drive Handling and static discharge precautionsBreather filter hole precautions Breather filter hole locationDrive as master with a non-ATA-compatible slave Jumper settingsMaster/slave configuration Cable-select optionDrive mounting Ultra ATA/100 cableMounting dimensions-top, side and end view DB35 Series 7200.2 Product Manual, Rev. D ATA interface signals and connector pins ATA interfaceSupported ATA commands Command name Command code in hexF6H Write Sectors Without Retries 31H Write Sectors Extended 34H Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Set Features command 0CH4 S.M.A.R.T. commands Code in features Register A.R.T. commandDB35 Series 7200.2 Product Manual, Rev. D Presales Support Seagate Technology support servicesInternet Technical SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index NumericsPage TMR DB35 Series 7200.2 Product Manual, Rev. D Page Seagate Technology LLC

Related manuals

Manual 56 pages 760 b