Seagate ST9300553SS, ST9300653SS, ST9300453SS manual AC power requirements, DC power requirements

Page 31

7.1.1PowerChoice reporting methods

PowerChoiceTM provides these reporting methods for tracking purposes:

Request Sense command reports

•Current power condition

•Method of entry

Note. Processing the Request Sense command does not impact the drive’s power save state.

Mode Sense command reports (mode page 0x1A)

•Idle conditions enabled / disabled

•Idle condition timer values (100ms increments) (default, saved, current, changeable)

Power Condition Vital Product Data (VPD) Page (VPD page 0x8A)

•Supported power conditions

•Typical recovery time from power conditions (1ms increments)

Start/Stop Cycle Counter Log Page reports (log page 0x0E)

• Specified and accumulated Start/Stops and Load/Unload cycles

Power Condition Transitions Log Page reports (log page 0x1A, subpage 0x00)

• Accumulated transitions to Active, Idle_A, Idle_B, Idle_C, Standby_Y, Standby_Z

7.2AC power requirements

None.

7.3DC power requirements

The voltage and current requirements for a single drive are shown below. Values indicated apply at the drive connector.

The standard drive models and the SED drive models have identical hardware, however the security and encryption portion of the drive controller ASIC is enabled and functional in the SED models. This represents a small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in power consumption. There is no additional drain on the 12V supply.

Savvio 15K.3 SAS Product Manual, Rev. A

23

Image 31

Contents SED FIPS140-2 Models ST9300653SSST9300553SS ST9146853SSST9146753SSST9300453SS ST9146653SS Standard Models Self-Encrypting Drive ModelsPage Contents Interface requirements Defect and error managementInstallation About Fips About self-encrypting drivesPage Savvio 15K.3 SAS Product Manual, Rev. a List of Figures Page Seagate Online Support and Services Seagate Technology support servicesScope Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean KCC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickEuropean Union Restriction of Hazardous Substances RoHS Reference documents Scsi Commands Reference Manual SAS Interface ManualGeneral description Media description Standard featuresReliability PerformanceFormatted capacities Programmable drive capacity Factory installed optionsAccess time Performance characteristicsInternal drive characteristics Seek performance characteristicsGeneral performance characteristics Format command execution timeStart/stop time Cache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataUnrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsPerformance impact Maximum processing delay4 S.M.A.R.T Controlling S.M.A.R.TPredictive failures Temperature Log Page 0Dh Parameter Code DescriptionThermal monitor Implementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bStorage Product warrantyShipping Product repair and return informationPowerChoiceTM power management Physical/electrical specificationsPowerChoice modes DC power requirements AC power requirementsRegulation 300GB models DC power requirements146GB models DC power requirements Power sequencing General DC power requirement notesConducted noise immunity Current profile for 300GB models Current profilesCurrent profile for 146GB models 300GB models in 6Gb operation Power dissipation300GB models in 3Gb operation 146GB models in 3Gb operation 146GB models in 6Gb operationEnvironmental limits Temperature a. OperatingRelative humidity Shock and vibration Effective altitude sea level a. OperatingShock Recommended mounting Vibration a. Operating-normalCorrosive environment Air cleanlinessAcoustics Dimensions Mechanical specificationsPurpose About FipsLevel 2 security Data encryption Controlled accessAdmin SP About self-encrypting drivesData bands Default passwordRandom number generator RNG Drive lockingCryptographic erase Authenticated firmware downloadPower requirements Supported commandsDrive internal defects/errors Defect and error managementDrive error recovery procedures Background Media Scan SAS system errorsDeferred Auto-Reallocation Media Pre-ScanIdle Read After Write Identifying a Protection Information drive Setting and determining the current Type LevelProtection Information PI Levels of PIDrive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresSupported commands Scsi commands supportedDual port support Supported commands Supported commands Supported commands Inquiry data Mode Sense dataSavvio inquiry data Page Mode Data Header Mode Data Header Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversGeneral interface characteristics SAS-2 Specification complianceLED drive signal Differential signalsNumerics IndexPage Msid Mtbf See also cooling Page Savvio 15K.3 SAS Product Manual, Rev. a