Seagate ST9300653SS, ST9300553SS, ST9300453SS Air cleanliness, Corrosive environment, Acoustics

Page 42

c.Non-operating

The limits of non-operating vibration shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives.

The drive shall not incur physical damage or degraded performance as a result of continuous vibration not exceeding:

5 - 22 Hz, swept sine: 0.25 G, (zero to peak)

22 - 350 Hz, swept sine: 5.0 G (zero to peak)

350 - 500 Hz, swept sine: 1.0 G (zero to peak)

10 - 500 Hz, random: 0.0118 G2/Hz Vibration may be applied in the X, Y, or Z axis.

7.5.5Air cleanliness

The drive is designed to operate in a typical office environment with minimal environmental control.

7.5.6Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment.

Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corro- sive chemicals as electronic drive component reliability can be affected by the installation environment. The sil- ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca- nized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

7.5.7Acoustics

Sound power during idle mode shall be 3.25 bels typical when measured to ISO 7779 specification.

Sound power during operating mode shall be 3.35 bels typical when measured to ISO 7779 specification.

There will not be any discrete tones more than 10 dB above the masking noise on typical drives when mea- sured according to Seagate specification 30553-001. There will not be any tones more than 24 dB above the masking noise on any drive.

7.5.8Electromagnetic susceptibility

See Section 3.1.1.1.

34

Savvio 15K.3 SAS Product Manual, Rev. A

Image 42
Contents Standard Models Self-Encrypting Drive Models ST9300653SSST9300553SS ST9146853SSST9146753SSST9300453SS ST9146653SS SED FIPS140-2 ModelsPage Contents About Fips About self-encrypting drives Defect and error managementInstallation Interface requirementsPage Savvio 15K.3 SAS Product Manual, Rev. a List of Figures Page Seagate Technology support services Seagate Online Support and ServicesScope Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityAustralian C-Tick Electromagnetic complianceElectromagnetic compliance for the European Union Korean KCCEuropean Union Restriction of Hazardous Substances RoHS Scsi Commands Reference Manual SAS Interface Manual Reference documentsGeneral description Standard features Media descriptionPerformance ReliabilityFormatted capacities Factory installed options Programmable drive capacitySeek performance characteristics Performance characteristicsInternal drive characteristics Access timeFormat command execution time General performance characteristicsStart/stop time Prefetch/multi-segmented cache control Cache operationCaching write data Prefetch operationRecoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenanceControlling S.M.A.R.T Maximum processing delay4 S.M.A.R.T Performance impactTemperature Log Page 0Dh Parameter Code Description Predictive failuresThermal monitor DST failure definition State of the drive prior to testingDrive Self Test DST ImplementationExtended test Function Code 010b Short and extended testsShort test Function Code 001b Log page entriesProduct repair and return information Product warrantyShipping StoragePhysical/electrical specifications PowerChoiceTM power managementPowerChoice modes AC power requirements DC power requirements300GB models DC power requirements Regulation146GB models DC power requirements General DC power requirement notes Power sequencingConducted noise immunity Current profiles Current profile for 300GB modelsCurrent profile for 146GB models Power dissipation 300GB models in 6Gb operation300GB models in 3Gb operation 146GB models in 6Gb operation 146GB models in 3Gb operationTemperature a. Operating Environmental limitsRelative humidity Effective altitude sea level a. Operating Shock and vibrationShock Vibration a. Operating-normal Recommended mountingAir cleanliness Corrosive environmentAcoustics Mechanical specifications DimensionsAbout Fips PurposeLevel 2 security About self-encrypting drives Controlled accessAdmin SP Data encryptionDrive locking Default passwordRandom number generator RNG Data bandsSupported commands Authenticated firmware downloadPower requirements Cryptographic eraseDefect and error management Drive internal defects/errorsDrive error recovery procedures SAS system errors Background Media ScanMedia Pre-Scan Deferred Auto-ReallocationIdle Read After Write Levels of PI Setting and determining the current Type LevelProtection Information PI Identifying a Protection Information driveInstallation Drive orientationCooling Air flowDrive mounting GroundingSAS features Interface requirementsScsi commands supported Supported commandsDual port support Supported commands Supported commands Supported commands Mode Sense data Inquiry dataSavvio inquiry data Page Mode Data Header Mode Data Header Miscellaneous operating features and conditions Miscellaneous featuresMiscellaneous status SAS physical interface Datum B Section C C Section a a Electrical description Physical characteristicsConnector requirements Pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutDifferential signals SAS-2 Specification complianceLED drive signal General interface characteristicsIndex NumericsPage Msid Mtbf See also cooling Page Savvio 15K.3 SAS Product Manual, Rev. a