Seagate ST373455FC manual Installation, Drive ID/option selection, Drive orientation, Cooling

Page 53

8.0Installation

Cheetah 15K.5 FC disc drive installation is a plug-and-play process. There are no jumpers, switches, or termi- nators on the drive. Simply plug the drive into the host’s 40-pin Fibre Channel backpanel connector (FC- SCA)—no cables are required. See Section 9.5 for additional information about this connector.

Use the FC-AL interface to select drive ID and all option configurations for devices on the loop.

If multiple devices are on the same FC-AL and physical addresses are used, set the device selection IDs (SEL IDs) on the backpanel so that no two devices have the same selection ID. This is called the hard assigned arbi- trated loop physical address (AL_PA). There are 125 AL_PAs available (see Table 27). If you set the AL_PA on the backpanel to any value other than 0, the device plugged into the backpanel’s SCA connector inherits this AL_PA. In the event you don’t successfully assign unique hard addresses (and therefore have duplicate selec- tion IDs assigned to two or more devices), the FC-AL generates a message indicating this condition. If you set the AL_PA on the backpanel to a value of 0, the system issues a unique soft-assigned physical address auto- matically.

Loop initialization is the process used to verify or obtain an address. The loop initialization process is per- formed when power is applied to the drive, when a device is added or removed from the Fibre Channel loop, or when a device times out attempting to win arbitration.

•Set all option selections in the connector prior to applying power to the drive. If you change options after applying power to the drive, recycle the drive power to activate the new settings.

•It is not necessary to low-level format this drive. The drive is shipped from the factory low-level formatted in 512-byte logical blocks. You need to reformat the drive only if you want to select a different logical block size.

8.1Drive ID/option selection

All drive options are made through the interface connector (J1). Table 24 provides the pin descriptions for the 40-pin Fibre Channel single connector (J1).

8.2Drive orientation

The drive may be mounted in any orientation. All drive performance characterizations, however, have been done with the drive in horizontal (discs level) and vertical (drive on its side) orientations, which are the two pre- ferred mounting orientations.

8.3Cooling

The host enclosure must dissipate heat from the drive. You should confirm that the host enclosure is designed to ensure that the drive operates within the temperature measurement guidelines described in Section 6.4.1. In some cases, forced airflow may be required to keep temperatures at or below the temperatures specified in Section 6.4.1.

Cheetah 15K.5 FC Product Manual, Rev. D

43

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Cheetah 15K.5 FC Page Cheetah 15K.5 FC Product Manual, Rev. D Cheetah 15K.5 FC Product Manual, Rev. D Contents Interface requirements Defect and error managementInstallation Seagate Technology support services Cheetah 15K.5 FC Product Manual, Rev. D List of Figures Page Scope Cheetah 15K.5 FC Product Manual, Rev. D Standards Applicable standards and reference documentationElectromagnetic compatibility Electromagnetic susceptibilityEuropean Union Restriction of Hazardous Substances RoHS Ncits TR-20 Reference documentsCheetah 15K.5 FC Product Manual, Rev. D General description Media description Standard featuresReliability PerformanceFormatted capacities Programmable drive capacityUser-installed accessories Factory-installed accessoriesFactory-installed options Internal drive characteristics Performance characteristicsSeek performance characteristics Access timeGeneral performance characteristics Format command execution time minutesStart/stop time Prefetch/multi-segmented cache controlCaching write data Cache operationPrefetch operation Error rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact MillisecondsDetermining rate Reporting controlPredictive failures Thermal monitorParameter Code Description State of the drive prior to testingDrive Self Test DST DST failure definitionShort and extended tests Invoking DSTShort test Function Code 001b Extended test Function Code 010bAbort Product warrantyShipping Product repair and return informationCheetah 15K.5 FC Product Manual, Rev. D AC power requirements Physical/electrical specificationsDC power requirements DC power requirements for ST3300655FC model Gbit AmpsDC power requirements for ST373455FC model Gbit Amps DC power requirements for ST3146855FC model Gbit AmpsPower sequencing General DC power requirement notesConducted noise immunity Current profilesTypical ST3300655FC drive, 4 Gbit, +12V current profile Typical ST3146855FC drive, 4 Gbit, +12V current profile Typical ST373455FC drive, 4 Gbit, +12V current profile ST3300655FC Power dissipationST3146855FC ST3146855FC CURRENT/POWER vs Throughput FC 4GBST373455FC CURRENT/POWER vs Throughput FC 4GB TemperatureEnvironmental limits ST373455FCEffective altitude sea level Relative humidityShock and vibration ShockPackage size Packaged/product weight Drop height Recommended mounting Vibration Air cleanlinessAcoustics Corrosive environmentRoHS compliance statement Mounting configuration dimensions Mechanical specificationsCheetah 15K.5 FC Product Manual, Rev. D Drive error recovery procedures Defect and error managementDrive internal defects/errors Page Background Media Scan FC-AL system errorsIdle Read After Write Media Pre-ScanDeferred Auto-Reallocation Drive ID/option selection InstallationDrive orientation CoolingAir flow Drive mountingGrounding Cheetah 15K.5 FC Product Manual, Rev. D Fibre Channel link service frames FC-AL featuresLink services supported Type of frame Interface requirementsFC Scsi FCP response codes Function name Response code Fibre Channel task management functionsFibre Channel task management responses NPort login Plogi payload Bytes Fibre Channel port loginFibre Channel Process Login Fibre Channel port login acceptNPort Login Accept ACC payload Bytes Process Login Plri payloadFibre Channel fabric login Fibre Channel Process Login AcceptProcess Login Accept ACC payload Bytes Fabric Login Flogi payload BytesFabric Login Accept ACC payload Bytes Fibre Channel fabric accept loginFibre Channel Arbitrated Loop options Dual port supportFC-AL options supported Option SupportedSupported commands Command code Command name Scsi commands supportedVerify error recovery page 07h Cheetah 15K.5 FC Product Manual, Rev. D Temperature page 0Dh Cheetah 15K.5 FC inquiry data Bytes Data hex Mode Sense dataInquiry data Page Mmode Sense 10 Byte Header Data Mode Sense 10 Byte Header Data 00 ae 00 10 00 00 00 08 08 8b b9 98 00 00 02 Miscellaneous features Miscellaneous operating features and conditionsSupported Feature or condition Miscellaneous statusPhysical description Physical characteristicsFC-AL physical interface Pin descriptions Connector requirementsElectrical description FC-AL transmitters and receivers FC-SCA pin descriptions Pin Signal name Signal typePin Signal name Signal type Fault LED Out PowerMotor start controls Enable port bypass signalsActive LED Out 11 SEL6 through SEL0 ID lines Parallel Enclosure Services Interface ESIHex Dec SettingArbitrated loop physical address Alpa values Device control codes Signal characteristicsTTL input characteristics FC Differential input LED driver signalsFC Differential output Receive eye diagram Eye diagram data values Link rate GHz Cheetah 15K.5 FC Product Manual, Rev. D Warranty Service Seagate Technology support servicesInternet MySeagate Spp.seagate.com Presales SupportData Recovery Services Data Recovery Services Authorized Service CentersToll-free support numbers FAX services-All Europe toll callCall center Presales and Technical Support Warranty Service Asia/Pacific support services Numerics IndexFAN Flogi Plogi Page See also cooling

ST3146855FC, ST373455FC, ST3300655FC specifications

Seagate is renowned for its commitment to high-performance data storage solutions, and their range of enterprise drives, including the ST3300655FC, ST373455FC, and ST3146855FC, demonstrates this dedication. These models cater to businesses requiring robust, reliable, and efficient hard disk drives (HDDs) designed for demanding environments.

The ST3300655FC offers a capacity of 300 GB, making it suitable for a variety of enterprise applications. It utilizes a 15,000 RPM spindle speed, which significantly enhances its performance, delivering quick read and write times. This drive supports Serial Attached SCSI (SAS) interface, ensuring faster data transfer rates and reliability essential for critical computing environments. The dual-port connectivity of SAS allows for enhanced fault tolerance and redundancy, making the ST3300655FC ideal for data centers and enterprise storage systems.

Following closely, the ST373455FC provides a slightly larger capacity of 734 GB while maintaining the same 15,000 RPM speed. This drive's design focuses on high availability, making it an excellent choice for applications that require continuous uptime. Like its counterpart, it also benefits from the SAS interface, ensuring that data can be accessed quickly and reliably. The robust construction of the ST373455FC guarantees consistent performance under heavy workloads, an essential characteristic for enterprise use.

The ST3146855FC, with a capacity of 146 GB, offers a balance between speed and storage for enterprises that do not require the larger capacities provided by the other two models. It also operates at 15,000 RPM, benefiting from similar technological advancements as the ST3300655FC and ST373455FC. This drive maintains compatibility with existing systems, making it a versatile option for organizations looking to upgrade their storage solutions without overhauling their infrastructure.

All three models exhibit Seagate's commitment to durability and low power consumption, which is critical for reducing operational costs in data centers. They also feature advanced error recovery and data integrity technologies, ensuring that critical data remains intact and accessible. Enhanced thermal and vibration tolerance further extends the lifespan of these drives in challenging environments.

In summary, the Seagate ST3300655FC, ST373455FC, and ST3146855FC are tailored to meet the rigorous demands of enterprise environments. Their high spindle speeds, SAS connectivity, and robust designs make them exemplary choices for businesses seeking reliable and efficient storage solutions. Their distinctive features and technologies ensure that they deliver outstanding performance, data integrity, and durability, making them invaluable assets in any data-driven organization.
Top Page Image Contents