Seagate ST36421A, ST32112A manual 4 S.M.A.R.T. commands, Code in Features Register A.R.T. Command

Page 38

30

U4 Family Product Manual, Rev. D

55H

Disable read look-ahead (read cache) feature.

82H

Disable write cache.

AAH

Enable read look-ahead (read cache) feature (default).

Note. At power-on, or after a hardware or software reset, the default values of the features are as indicated above.

3.2.4 S.M.A.R.T. commands

S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T. commands and implementation, see the Draft ATA-4 Standard.

This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the drive uses.

Code in Features

 

Register

S.M.A.R.T. Command

 

 

 

 

D0H

S.M.A.R.T. Read Data

D1H

Vendor-specific

 

 

D2H

S.M.A.R.T. Enable/Disable Attribute Autosave

 

 

D3H

S.M.A.R.T. Save Attribute Values

 

 

D4H

S.M.A.R.T. Execute Off-line Immediate

 

 

D7H

Vendor-specific

 

 

D8H

S.M.A.R.T. Enable Operations

 

 

D9H

S.M.A.R.T. Disable Operations

 

 

DAH

S.M.A.R.T. Return Status

 

 

Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04 (abort) is written to the Error register.

Image 38
Contents Product Manual Page Product Manual Page Contents Configuring and mounting the drive ATA interfaceFigures Seagate Connfidential Review Draft not for DistributionSeagate Confidential Review Draft not for Distribution Introduction Specification summary table Track-to-track seek time Msec typical Vibration, nonoperating Formatted capacity Default logical geometryLBA Mode Physical organizationRecording and interface technology Physical characteristicsDrive Specification ST38421A, ST36421A ST34311A, ST32112A Seek timeSpinup power Power specificationsPower consumption Start/stop timesOperating power and current Seek ModeRead/Write power and current Idle mode powerCurrent amps Time seconds Power Mode Typical Watts Typical Amps RMS 12VTypical current profile Voltage tolerance Power-management modesConducted noise Humidity Environmental tolerances Ambient temperatureTemperature gradient Relative HumidityShock Wet bulb temperatureAltitude Operating shockDrive acoustics Operating vibrationNonoperating vibration Reliability Agency certification Safety certificationElectromagnetic susceptibility Electromagnetic compatibilityFCC verification Australian C-TickU4 Family Product Manual, Rev. D Configuring and mounting the drive Handling and static-discharge precautionsJumper settings Master/slave configuration Master/slave jumper settingsUltra ATA/66 cable Important mounting precautionsCable-select option Drive mountingMounting dimensions-top, side and end view ATA interface signals and connector pins ATA interfaceO pins and supported ATA signals ATA Interface commands Supported ATA commands Command name Command code in hex ATA-standard commandsATA-standard power-management commands Identify Drive commandCommand name ATA-standard security commandsWord Description 27-46 Drive model number 40 Ascii char Multiword DMA active and modes Description if bit is set to Bit Word Set Features command 0CH4 S.M.A.R.T. commands Code in Features Register A.R.T. CommandPage U4 Family Product Manual, Rev. D U4 Family Product Manual, Rev. D
Related manuals
Manual 44 pages 34.49 Kb