Teledyne 2103c installation and operation guide Desiccant

Page 38

2103 Modem Module Section 5 Maintenance

5.3 Desiccant

The 2103 Modem uses desiccant to protect the internal compo- nents from moisture damage. The cartridge is filled with indi- cating silica gel, which is blue or yellow when dry. As the desiccant becomes saturated, the color changes from blue to pink, or from yellow to green. Replace the desiccant before the entire length of the cartridge turns pink or green.

5.3.1 Replacing the

The desiccant is contained in a cartridge located on the left side

Desiccant

of the 2103 Modem. To remove the cartridge, unscrew the collar

 

and slide the cartridge out of the 2103 Modem. The clear tube

 

reveals the silica gel desiccant inside.

Collar

To replace the silica gel desiccant:

 

1.

Hold the cartridge upright with the collar at the top.

 

2.

As shown in the margin, push the collar off the cartridge.

 

3.

Empty the saturated silica gel beads or granules.

 

4.

Fill the tube with new (Isco P/N 099-0011-03) or reacti-

 

 

vated (see section 3.3.2) silica gel desiccant.

 

5.

Press the collar onto the tube.

 

6.

Slide the cartridge into the 2103 Modem. Tighten the collar

 

 

to seal the cartridge in place.

Cartridge

 

 

5.3.2 Reactivating the

Silica gel beads and granules of desiccant can be reactivated.

Desiccant

 

CAUTION

 

 

 

Desiccant may produce irritating fumes when heated. Observe

 

the following precautions:

 

Use a vented oven in a well ventilated room.

 

Do not remain in the room while the regeneration is taking

 

 

place.

 

Use the recommended temperature. Avoid heating the

 

 

desiccant at higher than recommended temperatures.

There is the potential of irritating fumes coming from the des- iccant during reactivation. Because of this, we urge you to use caution, and to heat the desiccant in a well ventilated room. Material Safety Data Sheets are in the back of this manual.

The desiccant’s ability to remove moisture may lessen with each saturation/reactivation cycle, resulting in a need for more fre- quent service. After several cycles, the desiccant may no longer be effective as it saturates too quickly. At this point, replace the desiccant.

5-2

Image 38
Contents 2103/2103c Modem Module Page Foreword Page Table of Contents Modem ModuleAppendix C Material Safety Data Sheets Appendix a Replacement PartsAppendix B Accessories List of FiguresIntroduction Introduction Product DescriptionIdentifying Module Components 2103 Modem Module Components Top View2103 Modem Module Components Bottom View 2103 Modem Module Technical Specifications 2103 Communication Connector Pins Only Safety Symbols and Hazard Alerts 2103 Modem Cable ConnectorTechnical Service Modem Module Introduction Unpacking Instructions Installation and OperationSafety Installation Modem Module Installation and OperationTelephone Line Connection 2103 only 2103 Modem is in compliance with FCC part 68 rules. HoweverService is subject to state tariffs Modem Cable Connecting to Flowlink Flowlink Connect ScreenPushed Data Capability Modem Module Installation and Operation Antenna Options 2103c Cellular Modem ModuleOverview Programming Modem Module 2103c Cellular Modem ModuleSetting dialout phone numbers and alarm conditions TAP Service Parameters Modbus Protocol OperationEstablishing Configurations Configuration Example Direct Connection ShownGlossary of Terms Common Acronyms Modbus Ascii Address 1 Register Definitions Modbus Ascii Address 2-N+1 Register Definitions 117 Volume 1 status code Bit integer Read Measurement Parameters by Model Number Modem Module Modbus Protocol Maintenance Kit MaintenanceMaintenance Overview Desiccant DesiccantHydrophobic Filter Rings Modem Module Maintenance Appendix a Replacement Parts Replacement Parts1 2103 Replacement Parts Modem Module Appendix a Replacement Parts Modem Module Appendix a Replacement Parts 2 2103c Replacement Parts Modem Module Appendix a Replacement Parts Modem Module Appendix a Replacement Parts Modem Module Appendix a Replacement Parts Modem Module Appendix a Replacement Parts Modem Module Appendix a Replacement Parts Modem Module Appendix a Replacement Parts Modem Module Appendix a Replacement Parts Appendix B Accessories How to Order General AccessoriesModem Module Appendix B Accessories Appendix C Material Safety Data Sheets Material Safety Data Sheet Health Hazard Data Material Safety Data Sheet First Aid Measures Exposure Controls/Personal Protection Toxicological Information Other Information Declaration of Conformity Page Control and Laboratory use Page Teledyne Isco One Year Limited Factory Service Warranty