Tyan Computer Transport FT48 manual Jumpers & Connectors Jumper/Connector Function, JP2

Page 21

1.5.7 Jumpers & Connectors

	Jumper/Connector	Function

	J1	SMBUS Connector

	J14	Fan Connector (for barebone use only)

	J20	Clear CMOS Jumper
		- Pin 2-3 closed: Normal (Default)
		- Pin 1-2 closed: Clear

	J22	NMI Header

	J30/J95	USB Front Panel Connector
		J30: USB2
		J95: USB3

	J101	COM2 Header

	J115	Front Panel Header

	JP1	RI Header

	JP2	Intruder Header

	CPUFAN0/1/2/3	CPU Fan Connectors

	SYSFAN0/1/2/3/4/5/6/7	Chassis Fan Connectors

	SATA0/1/2/3/4/5/6/7	Serial ATA RAID Connectors

Chapter 1: Overview

13

Image 21

Contents Transport FT48 B4985 Service Engineer’s Manual Page Copyright DisclaimerTrademark Recognition Federal Communications Commission About this Manual Safety Information Table of Contents Fan Board Connector Pin Definition Replacing Pre-installed ComponentsAbout the Tyan Transport FT48-B4985 OverviewB4985F48V8HR Rackmount B4985F48V8HR Tower Product ModelEnclosure FeaturesUnpacking Box Contents Component DescriptionComponent Description Accessories Sliding Rail Kit System Front View and Front Panel About the ProductSystem Rear View Color Description System Top View for FAN LEDsFront LEDs Color State DescriptionStatus Color Description Rear I/O LEDsMotherboard Layout JP2 Jumpers & Connectors Jumper/Connector FunctionMotherboard Block Diagram System Internal View Model Picture Quantity Description Number Standard Parts FRU ListModel Picture Quantity Description Number Model Picture Quantity Description Before You Begin Work AreaTools Precautions Removing the Chassis Cover Installing Motherboard ComponentsInstalling the CPUs and Heatsinks Setting Up Setting Up Installing the Memory Setting Up Refer to the following table for supported DDR2 populations Installing the PCI-E/PCI Cards Setting Up Installing Hard Drives Setting Up Installing the Expansion DVD-ROM Option Setting Up Setting Up Installing the Floppy Disk Drive Option Setting Up Setting Up Setting Up Installing the LCM Kit Option Setting Up Installing the Long Cards Tower Installing the 5.25 Devices in Tower PositionSetting Up Setting Up Installing Chassis Foot Stands Installing the Server in a Rack Rack MountingScrews List Installing the Inner Rails to the Unit Installing the Outer Rails to the Rack Setting Up Rackmounting the Server Setting Up Opening the Chassis Front Bezel Installing the Security Tab Setting Up Introduction Replacing Pre-installed ComponentsPrecautions Following flowchart outlines the disassembly procedure Disassembly FlowchartRemoving the Chassis Cover Removing the Front Door Assembly Replacing Motherboard Components Disconnecting All Motherboard CablesReplacing the Motherboard Replacing the Cooling Fans Replacing the Fan Control Board Replacing Pre-installed Components Fan Board Features Fan Board Connector Pin Definition Replacing the SAS/SATA Backplane Replacing Pre-installed Components Rear View 1 M1211-P SAS/SATA Backplane Features2 M1211-P SAS/SATA Backplane Connector Pin Definition Replacing the LED Control Board Replacing Pre-installed Components 1 M1007 LED Control Board Features 2 M1007 LED Control Board Connector Pin Definition Replacing the DVD-ROM Replacing Pre-installed Components Replacing the Redundant Power Supply B4985 Advanced/Hardware Health Information Appendix I Bios DifferencesTable of Differences S4985 B4985 S4985 Advanced/Hardware Monitor InformationPower Supply Cables SAS/SATA CablesFAN Cables Power Supply to FAN Board LED Control Board to Motherboard Other CablesAppendix III Installing the Smdc Card Option Page Cable Connection Table Appendix IV Installing Expansion Hard Drives Rackmount installation to Page Tower installation to Page Help Resources Technical SupportReturning Merchandise for Service