Tyan Computer Transport FT48 manual Rack Mounting, Installing the Server in a Rack, Screws List

Page 54

2.9Rack Mounting

After installing the necessary components, the Transport FT48-B4985 can be mounted in a standard rack using the sliding rail kit.

Sliding rail kit Rail assembly x 2 Mounting ears x 2 Screws kit x 3

2.9.1Installing the Server in a Rack

Follow these instructions to mount the FT48-B4985 into an industry standard 19" rack.

NOTE: Before mounting the Transport FT48-B4985 in a rack, ensure that all internal components have been installed and that the unit has been fully tested. Maintenance can be performed on the unit while in a rack but it is preferable to install the device in a fully operational condition.

Screws List

No.	Screw	Size	Quantity

A		Bracket for	10
A		M6 screw	10
		M6 screw

B		M6	10

C		M4-L5	16

46	Chapter 2: Setting Up

Image 54

Contents Transport FT48 B4985 Service Engineer’s Manual Page Copyright DisclaimerTrademark Recognition Federal Communications Commission About this Manual Safety Information Table of Contents Replacing Pre-installed Components Fan Board Connector Pin DefinitionOverview About the Tyan Transport FT48-B4985Product Model B4985F48V8HR Rackmount B4985F48V8HR TowerFeatures EnclosureBox Contents Component Description UnpackingComponent Description Accessories Sliding Rail Kit About the Product System Front View and Front PanelSystem Rear View Front LEDs System Top View for FAN LEDsColor Description Color State DescriptionRear I/O LEDs Status Color DescriptionMotherboard Layout Jumpers & Connectors Jumper/Connector Function JP2Motherboard Block Diagram System Internal View FRU List Model Picture Quantity Description Number Standard PartsModel Picture Quantity Description Number Model Picture Quantity Description Before You Begin Work AreaTools Precautions Installing Motherboard Components Removing the Chassis CoverInstalling the CPUs and Heatsinks Setting Up Setting Up Installing the Memory Setting Up Refer to the following table for supported DDR2 populations Installing the PCI-E/PCI Cards Setting Up Installing Hard Drives Setting Up Installing the Expansion DVD-ROM Option Setting Up Setting Up Installing the Floppy Disk Drive Option Setting Up Setting Up Setting Up Installing the LCM Kit Option Setting Up Installing the Long Cards Installing the 5.25 Devices in Tower Position TowerSetting Up Setting Up Installing Chassis Foot Stands Installing the Server in a Rack Rack MountingScrews List Installing the Inner Rails to the Unit Installing the Outer Rails to the Rack Setting Up Rackmounting the Server Setting Up Opening the Chassis Front Bezel Installing the Security Tab Setting Up Replacing Pre-installed Components IntroductionPrecautions Disassembly Flowchart Following flowchart outlines the disassembly procedureRemoving the Chassis Cover Removing the Front Door Assembly Disconnecting All Motherboard Cables Replacing Motherboard ComponentsReplacing the Motherboard Replacing the Cooling Fans Replacing the Fan Control Board Replacing Pre-installed Components Fan Board Features Fan Board Connector Pin Definition Replacing the SAS/SATA Backplane Replacing Pre-installed Components 1 M1211-P SAS/SATA Backplane Features Rear View2 M1211-P SAS/SATA Backplane Connector Pin Definition Replacing the LED Control Board Replacing Pre-installed Components 1 M1007 LED Control Board Features 2 M1007 LED Control Board Connector Pin Definition Replacing the DVD-ROM Replacing Pre-installed Components Replacing the Redundant Power Supply Appendix I Bios Differences B4985 Advanced/Hardware Health InformationS4985 Advanced/Hardware Monitor Information Table of Differences S4985 B4985Power Supply Cables SAS/SATA CablesFAN Cables Power Supply to FAN Board Other Cables LED Control Board to MotherboardAppendix III Installing the Smdc Card Option Page Cable Connection Table Appendix IV Installing Expansion Hard Drives Rackmount installation to Page Tower installation to Page Technical Support Help ResourcesReturning Merchandise for Service