Tyan Computer S2877 warranty 13 *Front Panel Audio Header *P53

Page 19

2.3.13 *Front Panel Audio Header: *P53

Signal

Pin

Pin

Signal

Description

#

#

Description

 

 

 

 

AUD_MIC_L

1

2

GND

 

 

 

 

AUD_MIC_R

3

4

AVDD

 

 

 

 

AUD_FP_R

5

6

AUD_RET_R

 

 

 

 

F_AUD_DET

7

8

KEY

 

 

 

 

AUD_FP_L

9

10

AUD_RED_L

 

 

 

 

Note: a. If you use onboard Audio port, you must close Pin5-Pin6 and Pin9-Pin10.

b. P53 is only available on S2877ANRF version.

2.3.14 CPU FAN Connector: J9/J37

PIN1

Use these connectors to connect processor cooling fans to your motherboard.

J9 for CPU1 & J37 for CPU2.

This 4-pin fan connector supports a new standard fan with integrated fan speed control on the fan itself for better fan life.

19

http://www.tyan.com

Image 19
Contents Trademark CopyrightVersion Board Installation Table of Contents IntroductionBios Page Congratulations Hardware SpecificationsExpansion Slots Integrated FireWire Ieee1394A Controller Anrf version onlyOS Operating System Support Software SpecificationsPage Board Installation Board Image Tiger K8WE S2877 Block Diagram Block DiagramBoard Parts, Jumpers and Connectors Jumper Legend Jumper/Connector Function SettingsFront Panel Header J139 Function DefaultClear Cmos Header J112 Pin-1 4 *FireWire IEEE1394A Enable/Disable Jumper *J147Chassis Intrusion Header J77 Pin-2Buzzer/External Speaker Header J14 5 *FireWire IEEE1394A Pin Header *J148/*J149Open Pin3 and Pin4 USB 2.0 Front Panel Headers J25/J140 7 COM2 Connector J42S2877G2NR version Keyboard Lock Connector J13Open Closed Gigabit LAN1/**LAN2 Front Panel Header J2/ **J311 **VGA ATI Rage XL Enable/ Disable Jumper **J85 13 *Front Panel Audio Header *P53 Chassis 3-pin FAN Connectors J36/J10 Chassis 4-pin FAN Connector J4717 3-pin or 4-pin fan support selection jumper J5 Installing the Processors Heatsink Retention Frame Installation Thermal Interface Material Type a CAM Lever Type Installation Heatsink Installation ProceduresType B Screw Retention Type Heatsink Finishing Installing the Heatsink Tips on Installing Motherboard in Chassis Installing the Memory CPU1 CPU2 DIMM-A1 DIMM-A2 DIMM-B1 DIMM-B2 Memory Installation Procedure Attaching IDE Drive Cable Attaching Drive CablesPage Installing Add-In Cards Onboard LAN LED Color Definition Connecting External DevicesTips on modifying I/O shielding for Anrf and G2NR version Installing the Power SupplyFinishing Up Applying power to the boardPage To select an item Bios Setup UtilityBios Legend Bar Bios Menu BarGetting Help Feature Option Description Bios Main MenuMenu Item Bios Advanced MenuHammer Configuration Sub-Menu Limit DisabledIntegrated Devices Sub-Menu AutoEnabled Feature Option Description DisabledNV Configuration PCI Configuration Sub-Menu PCI Device, Slot # 1 ,2,3 Add On Onboard Device ControlAvailable PCI/PNP ISA UHB Region ExclusionPCI/PNP ISA IRQ Resource Exclusion Feature Option Description AvailableOther IDE Configuration Sub-MenuBoth Standard Primary Master/Slave, Secondary Master/SlaveFloppy Configuration Sub-Menu 3F8 6 I/O Device Configuration Sub-MenuNormal Primary Hardware Monitor Sub-Menu378 Output only115200 VT100 Console Redirection Sub-Menu19200 38400 57600Direct Watchdog Timer Option Sub-Menu~255 Memory Bios Memory MenuUshc Security MenuUser Bios Boot MenuALL PCI Scsi Boot Device PriorityEnabled Power MenuStay Off Bios Exit Menu Page Flash Utility Beep CodesMemory, Video, CPU Code Beeps / Description Bios Post CodeApic Code Beeps / Description Glossary Page Page Page Page Page Technical Support Returning Merchandise for ServiceDocument # D1681-100
Related manuals
Manual 77 pages 40.96 Kb