Tyan Computer Tyan S1598 user manual Flash Memory Writer

Page 59

FLASH MEMORY WRITER V3.0

Copyright(C) 1993, AWARD SOFTWARE, INC.

For VX/HX-2A59CT51

Date:4/13/98

File Name to Program:

Error Message:

Type in the whole file name, e.g. A61AW10.BIN, and confirm that you want to program the BIOS. The utility will then “Blank,” “Erase,” and “Program” the flash memory on the mainboard with the new BIOS file. You should choose “Yes” to save the original system BIOS to a floppy diskette before you program the new BIOS. This leaves you with a backup of your original BIOS in case you need to re-install it. If you cannot successfully program the new BIOS file for some reason, re-install your original BIOS from the backup file. Remember, always reset the CMOS after flashing to a new BIOS (see page 33).

Warning: If you do not successfully install a complete BIOS file in the flash memory on the mainboard, your system may not be able to boot. If this happens, it will require service by your system vendor. Follow the instructions in this section precisely to avoid such an inconvenience.

BIOS

S1598 Trinity ATX

59

Image 59

Contents Motherboard User’s Manual Revision Tyan S1598Table of Contents This page has been intentionally left blank Overview ChapterIcons Hardware Specifications/FeaturesSystem Memory Bios InformationOn Board Cache Chipset InformationOn BoardAudio Manufacturing Option Software SpecificationsOther Features Technical SupportFor Resellers Only Returning Merchandise for ServiceHelp resources What’s the first thing I should do? PrecautionsUnpacking Do Notapply Power to the Board if IT has Been Damaged Installation StepsPin jumpers Or more pin jumpers Off Open What is a Jumper?Dimm Map of Motherboard JumpersPicture of Motherboard Features CPU Clock Multiplier Setting JumpersCPU Bus Speed Settings CPU Core Voltage SettingsFAN Pin Assignments 66MHz. The benefit of this setting is that you canHardware Cmos & Password Reset J3 External Pin AssignmentsMounting the Motherboard in the Chassis Acpi Bi-Color LED Connector J5Soft Power Connector Speaker Connector InstallationDimm Bank Total Installing MemoryChapter Cache Memory CPU Installing the CPU and Cooling FanInstall Connecting IDE and Floppy Drives Connecting Floppy Drives Connecting the Power SupplyInstalling Add-on Cards Connecting PS/2, USB, Serial & Parallel Devices You are done Frequently Asked QuestionsInstall Chapter This page intentionally left blank Introduction to Setup Bios ConfigurationSetup Keys Key Function Setup Variations Main Setup MenuPower Management Setup Standard Cmos SetupBios Features Setup Chipset Features SetupTime Standard Cmos SetupDate Chapter Halt On Floppy 3 Mode SupportDrive A, Drive B VideoMemory Bios Features SetupSe tting Option Bios De fault Se tup De fault Bios Feature Setup Default Settings ChartVirus Warning Settings ChartQuick Power On Self Test Boot SequenceTypematic Delay Msec Boot Up Floppy SeekBoot Up NumLock Status Typematic Rate SettingOS Select for Dram 64MB Video Bios ShadowSecurity Option PCI/VGA Palette SnoopAdvanced Options Chipset Features SetupDram Read Pipeline Chipset Features Setup Default Settings ChartBank 0/1, 2/3, 4/5 Dram Timing Sdram Cycle LengthMemory Hole at 15MbAddr Video Bios CacheableSystem Bios Cacheable Cache TimingIRQ7LPT1 Power Management SetupPM Control byAPM Power ManagementAcpi Function Video Off Method PM TimersHDD Power Down Video Off OptionPM Events Doze ModeSuspend Mode RTC Alarm ResumeIRQn Processed. Secondary interrupts are typicallyPnP / PCI Configuration Default Settings Chart PnP/PCI ConfigurationResources Controlled By PNP OS InstalledReset Configuration Data DMA-nAssigned to PCI Delay TransactionPCI#2 Access #1 Retry IRQ-nAssigned toIntegrated Peripherals On-Chip PCI IDE First/Second Channel Integrated Peripherals Default Settings ChartIDE Prefetch Mode IDE HDD Block Mode Onboard Serial Port 1 IDE Primary/Secondary Master/Slave Udma Init Display First Onboard FDD ControllerFlash Writer Utility User PasswordChapter Flash Memory Writer Beep Bios ROM checksum error System haltedCmos battery failed Post MessagesCPU at nnnn Cmos checksum error Defaults loadedDisplay switch is set incorrectly Keyboard error or no keyboard presentMemory test fail Override enabled Defaults loadedKeyboard is locked out Unlock the key Memory TestThis page has been intentionally left blank Appendix Glossary Appendix Glossary Appendix Glossary Appendix Document # D1353-100 See pages 14-16 for details on Jumpers Jumper Settings Quick Reference