Tyan Computer Tyan S1598 user manual Document # D1353-100

Page 71

Notice for the USA

Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC Part 15: This Device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1)this device may not cause harmful interference, and

2)this device must accept any interference received including interference that may cause undesired operation. If this equipment does cause harmful interfer- ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Plug the equipment into an outlet on a circuit different from that of the receiver.

Consult the dealer or an experienced radio/television technician for help.

CAUTION: LITHIUM BATTERIES included with This PC board. Danger of explosion if battery is incorrectly replaced. Replace ONLY with the same or equivalent type recommended by manufacturer. Dispose of used batteries according to manufacturer instructions.

Notice for Canada

This apparatus complies with the Class B limits for radio interference as specified in the Canadian Department of Communications Radio Interference Regulations.

Cet appareil est conforme aux normes de Classe B d’ interference radio tel que spécifié par le Ministére Canadien des Communications dans les réglements d’interférence radio.

Notice for Europe (CE Mark)

This product is in conformity with the Council Directive 89/336/EEC, 92/31/EEC (EMC).

Document # D1353-100

S1598 Trinity ATX

71

Image 71
Contents Motherboard User’s Manual Revision Tyan S1598Table of Contents This page has been intentionally left blank Overview ChapterIcons Hardware Specifications/FeaturesSystem Memory Bios InformationOn Board Cache Chipset InformationOn BoardAudio Manufacturing Option Software SpecificationsOther Features Technical SupportFor Resellers Only Returning Merchandise for ServiceHelp resources What’s the first thing I should do? PrecautionsUnpacking Do Notapply Power to the Board if IT has Been Damaged Installation StepsPin jumpers Or more pin jumpers Off Open What is a Jumper?Dimm Map of Motherboard JumpersPicture of Motherboard Features CPU Clock Multiplier Setting JumpersCPU Bus Speed Settings CPU Core Voltage SettingsFAN Pin Assignments 66MHz. The benefit of this setting is that you canHardware Cmos & Password Reset J3 External Pin AssignmentsMounting the Motherboard in the Chassis Acpi Bi-Color LED Connector J5Soft Power Connector Speaker Connector InstallationDimm Bank Total Installing MemoryChapter Cache Memory CPU Installing the CPU and Cooling FanInstall Connecting IDE and Floppy Drives Connecting Floppy Drives Connecting the Power SupplyInstalling Add-on Cards Connecting PS/2, USB, Serial & Parallel Devices You are done Frequently Asked QuestionsInstall Chapter This page intentionally left blank Introduction to Setup Bios ConfigurationSetup Keys Key Function Setup Variations Main Setup MenuPower Management Setup Standard Cmos SetupBios Features Setup Chipset Features SetupTime Standard Cmos SetupDate Chapter Halt On Floppy 3 Mode SupportDrive A, Drive B VideoMemory Bios Features SetupSe tting Option Bios De fault Se tup De fault Bios Feature Setup Default Settings ChartVirus Warning Settings ChartQuick Power On Self Test Boot SequenceTypematic Delay Msec Boot Up Floppy SeekBoot Up NumLock Status Typematic Rate SettingOS Select for Dram 64MB Video Bios ShadowSecurity Option PCI/VGA Palette SnoopAdvanced Options Chipset Features SetupDram Read Pipeline Chipset Features Setup Default Settings ChartBank 0/1, 2/3, 4/5 Dram Timing Sdram Cycle LengthMemory Hole at 15MbAddr Video Bios CacheableSystem Bios Cacheable Cache TimingIRQ7LPT1 Power Management SetupPM Control byAPM Power ManagementAcpi Function Video Off Method PM TimersHDD Power Down Video Off OptionPM Events Doze ModeSuspend Mode RTC Alarm ResumeIRQn Processed. Secondary interrupts are typicallyPnP / PCI Configuration Default Settings Chart PnP/PCI ConfigurationResources Controlled By PNP OS InstalledReset Configuration Data DMA-nAssigned to PCI Delay TransactionPCI#2 Access #1 Retry IRQ-nAssigned toIntegrated Peripherals On-Chip PCI IDE First/Second Channel Integrated Peripherals Default Settings ChartIDE Prefetch Mode IDE HDD Block ModeOnboard Serial Port 1 IDE Primary/Secondary Master/Slave UdmaInit Display First Onboard FDD ControllerFlash Writer Utility User PasswordChapter Flash Memory Writer Beep Bios ROM checksum error System haltedCmos battery failed Post MessagesCPU at nnnn Cmos checksum error Defaults loadedDisplay switch is set incorrectly Keyboard error or no keyboard presentMemory test fail Override enabled Defaults loadedKeyboard is locked out Unlock the key Memory TestThis page has been intentionally left blank Appendix Glossary Appendix Glossary Appendix Glossary Appendix Document # D1353-100 See pages 14-16 for details on Jumpers Jumper Settings Quick Reference