Tyan Computer Tyan S1598 user manual Unpacking, Precautions, What’s the first thing I should do?

Page 9

chapter 2

Board Installation

Unpacking

The mainboard package should contain the following:

(1) S1598 mainboard

(1) 40-pin IDE and 34-pin floppy cable pack

(1) S1598 User’s Manual

(1) Driver CD

Precautions

What’s the first thing I should do?

The first thing you should do is read this user’s manual. It contains important information which will make configuration and setup much easier.

Here are some precautions you should follow when installing your mother- board:

(1)Ground yourself properly before removing your motherboard from the antistatic bag. Unplug the power from your computer

S1598 Trinity ATX

INSTALL

9

Image 9

Contents Motherboard User’s Manual Revision Tyan S1598Table of Contents This page has been intentionally left blank Overview ChapterIcons Hardware Specifications/FeaturesOn Board Cache Bios InformationChipset Information System MemoryOther Features Software SpecificationsTechnical Support On BoardAudio Manufacturing OptionReturning Merchandise for Service Help resourcesFor Resellers Only Precautions UnpackingWhat’s the first thing I should do? Do Notapply Power to the Board if IT has Been Damaged Installation StepsPin jumpers Or more pin jumpers Off Open What is a Jumper?Dimm Map of Motherboard JumpersPicture of Motherboard Features CPU Bus Speed Settings Setting JumpersCPU Core Voltage Settings CPU Clock MultiplierHardware Cmos & Password Reset 66MHz. The benefit of this setting is that you canJ3 External Pin Assignments FAN Pin AssignmentsSoft Power Connector Acpi Bi-Color LED Connector J5Speaker Connector Installation Mounting the Motherboard in the ChassisDimm Bank Total Installing MemoryChapter Cache Memory CPU Installing the CPU and Cooling FanInstall Connecting IDE and Floppy Drives Connecting Floppy Drives Connecting the Power SupplyInstalling Add-on Cards Connecting PS/2, USB, Serial & Parallel Devices You are done Frequently Asked QuestionsInstall Chapter This page intentionally left blank Introduction to Setup Bios ConfigurationSetup Keys Key Function Setup Variations Main Setup MenuBios Features Setup Standard Cmos SetupChipset Features Setup Power Management SetupStandard Cmos Setup DateTime Chapter Drive A, Drive B Floppy 3 Mode SupportVideo Halt OnMemory Bios Features SetupSe tting Option Bios De fault Se tup De fault Bios Feature Setup Default Settings ChartQuick Power On Self Test Settings ChartBoot Sequence Virus WarningBoot Up NumLock Status Boot Up Floppy SeekTypematic Rate Setting Typematic Delay MsecSecurity Option Video Bios ShadowPCI/VGA Palette Snoop OS Select for Dram 64MBAdvanced Options Chipset Features SetupBank 0/1, 2/3, 4/5 Dram Timing Chipset Features Setup Default Settings ChartSdram Cycle Length Dram Read PipelineSystem Bios Cacheable Video Bios CacheableCache Timing Memory Hole at 15MbAddrIRQ7LPT1 Power Management SetupPower Management Acpi FunctionPM Control byAPM HDD Power Down PM TimersVideo Off Option Video Off MethodSuspend Mode Doze ModeRTC Alarm Resume PM EventsIRQn Processed. Secondary interrupts are typicallyPnP / PCI Configuration Default Settings Chart PnP/PCI ConfigurationPNP OS Installed Reset Configuration DataResources Controlled By PCI#2 Access #1 Retry PCI Delay TransactionIRQ-nAssigned to DMA-nAssigned toIntegrated Peripherals IDE Prefetch Mode Integrated Peripherals Default Settings ChartIDE HDD Block Mode On-Chip PCI IDE First/Second ChannelInit Display First IDE Primary/Secondary Master/Slave UdmaOnboard FDD Controller Onboard Serial Port 1Flash Writer Utility User PasswordChapter Flash Memory Writer Cmos battery failed Bios ROM checksum error System haltedPost Messages BeepDisplay switch is set incorrectly Cmos checksum error Defaults loadedKeyboard error or no keyboard present CPU at nnnnKeyboard is locked out Unlock the key Override enabled Defaults loadedMemory Test Memory test failThis page has been intentionally left blank Appendix Glossary Appendix Glossary Appendix Glossary Appendix Document # D1353-100 See pages 14-16 for details on Jumpers Jumper Settings Quick Reference