Tyan Computer B3970-U manual Jumpers & Connectors Function, JP8

Page 18

Jumpers & Connectors

Jumper

/Connector

Function

J2/J3

3-pin Back Panel Fan Connector

 

 

J4/J22/J23/

4-pin Fan Connector with Speed Control

J35

 

 

 

J6

COM2 Header

 

 

J24

USB Front Panel Connector

 

 

J25

Front Panel SATA LED Pin Header

 

 

J26

Front Panel Header

 

 

J27

LCM Pin Header

 

 

J29

IPMB Pin Header

 

 

JP1

VGA Enable/Disable Jumper

 

(Close 1-2) Default, Enabled

 

(Close 2-3) Disabled

 

 

JP2/JP3

SMDC/ASF2.0 Select Jumper

 

(Close 1-2) Default, support ASF2.0

 

(Close 2-3) support SMDC card

 

 

JP6

PCI-X Frequency Select Jumper

 

Open: 100MHz

 

Installed: Default, 133MHz

 

 

JP8

Clear CMOS Jumper

 

(Close 1-2) Default

 

(Close 2-3) Clear CMOS

 

 

J21

TARO SO-DIMM Socket

 

 

J36

SMDC Connector

 

 

J5/J28

Reserved for OEM only

 

 

10

Chapter 1: Overview

Image 18
Contents Transport GT20 B3970-U Service Engineer’s Manual Page Copyright DisclaimerTrademark Recognition Federal Communications Commission FCC About this Manual IiiSafety Information Table of Contents Overview Setting UpReplacing Pre-Installed Components Page About the Transport GT20 B3970-U Product ModelOverview Features EnclosureUnpacking FDD KitRail Kit About the Product Front ViewRear View LED Definition Front Panel Rear I/O LEDInternal View Motherboard S3970 Block Diagram Motherboard Layout Overview Jumpers & Connectors Function JP8Work Area Setting UpBefore You Begin ToolsPrecautions Installing the Server in a Rack Rack MountingRack mounting kit Installing the Inner Rails to Chassis Installing Outer Rails to the RackLocate the front and rear brackets Mounting Bracket Rackmounting the Server Setting Up Installing Motherboard Components Removing the Chassis CoverInstalling the Memory Installing the CPU and Heatsink Setting Up Setting Up Installing the PCI-X Card Setting Up Installing the External Hard Drive Setting Up Installing the Slim FDD Option Connect the other side to the connector on motherboard Setting Up Replacing Pre-Installed Components IntroductionReplacing Pre-Installed Components Disassembly Flowchart Following flowchart outlines the disassembly procedureRemoving the Cover Disconnecting All Motherboard Cables Main Power EPS 12V PowerReplacing Motherboard Components Removing the Motherboard Replacing the Slim CD-ROM Replacing Pre-Installed Components Replacing the LED Control Board Replacing Pre-Installed Components Replacing the M1012 Adapter Board LAN/IDFan Cables 1 M1012 Adapter Board Features for B3970-U J3 LAN/ID LED2 M1012 Adapter Board Connector Pin Definition FAN Signal Related Connector Pin Definition GND FAN1TACH FAN2TACH FAN3TACH KEY PIN FAN312VPWM FAN3TACH GND FAN4TACH FAN412VPWM FAN912VPWM FAN9TACH GND FAN10TACH Replacing the Sata Backplane Replacing Pre-Installed Components 1 SAS/SATA Backplane M1208 Features J4, SAS/SATA Replacing the Power Supply Replacing Pre-Installed Components Appendix I Bios Differences B3970-U Advanced/Hardware Health ConfigurationS3970 Advanced/Hardware Health Configuration Bios Setup Utility AdvancedB3970-UG20S4H Model Sata CableFAN Cable System Fan to M1012 Adapter BoardPower Supply to M1012 Adapter Board Power Supply CablePower Supply to Motherboard Power Supply to M1208 Sata BackplaneCD-ROM Related Cable Other CablesM1003 Front Panel Control Board Related Cable FDD Related Cable OptionAppendix III Installing Smdc Cards Installing M3289 into HDD Tray Page Installing M3290/M3291 into HDD tray Page Installing M3290/M3291 into GT24 Chassis Page Page Technical Support Help ResourcesReturning Merchandise for Service