Tyan Computer Appendix I Bios Differences, B3970-U Advanced/Hardware Health Configuration

Page 63

Appendix I: BIOS Differences

The BIOS of B3970-U is similar to the BIOS of S3970G2N-U. There is only one menu different. You may refer to the attached motherboard manual for the complete BIOS infor- mation. The differences between B3970-U and S3970G2N-U is on the “Advanced/Hardware Health Configuration” menu. See the following for the differences.

B3970-U Advanced/Hardware Health Configuration

Advanced

BIOS Setup Utility

 

 

 

 

 

 

 

 

Hardware Health Configuration

 

Enables Hardware

 

 

Health Monitoring

H/W Health Function

[Enabled]

Device

 

 

FAN Select

[3Pin FAN]

 

 

AutoFAN1 Power Control

[Enabled]

 

 

PWM Minimal Duty Cycle

[10% Duty Cycle]

 

 

FAN Fail LED Indicator

[Enabled]

 

 

Hardware Health Event Monitoring

 

 

 

 

 

 

XMainboard Voltages Report

 

 

 

CPU1 Temperature

:xx ºC/ xxx ºF

ÅÆ Select Screen

Mainboard Ambient Temp.

:xx ºC/ xxx ºF

 

 

ÇÈ

Select Item

System FAN1 Speed

:xxxx RPM

+ -

Change Option

System FAN2 Speed

:xxxx RPM

F1

General Help

System FAN3 Speed

:xxxx RPM

F10

Save and Exit

System FAN4 Speed

:xxxx RPM

ESC

Exit

 

 

 

 

55

Image 63
Contents Transport GT20 B3970-U Service Engineer’s Manual Page Copyright DisclaimerTrademark Recognition Federal Communications Commission FCC Iii About this ManualSafety Information Table of Contents Overview Setting UpReplacing Pre-Installed Components Page About the Transport GT20 B3970-U Product ModelOverview Enclosure FeaturesFDD Kit UnpackingRail Kit About the Product Front ViewRear View Rear I/O LED LED Definition Front PanelInternal View Motherboard S3970 Block Diagram Motherboard Layout Overview JP8 Jumpers & Connectors FunctionTools Setting UpBefore You Begin Work AreaPrecautions Installing the Server in a Rack Rack MountingRack mounting kit Installing Outer Rails to the Rack Installing the Inner Rails to ChassisLocate the front and rear brackets Mounting Bracket Rackmounting the Server Setting Up Removing the Chassis Cover Installing Motherboard ComponentsInstalling the Memory Installing the CPU and Heatsink Setting Up Setting Up Installing the PCI-X Card Setting Up Installing the External Hard Drive Setting Up Installing the Slim FDD Option Connect the other side to the connector on motherboard Setting Up Introduction Replacing Pre-Installed ComponentsReplacing Pre-Installed Components Following flowchart outlines the disassembly procedure Disassembly FlowchartRemoving the Cover Disconnecting All Motherboard Cables Main Power EPS 12V PowerReplacing Motherboard Components Removing the Motherboard Replacing the Slim CD-ROM Replacing Pre-Installed Components Replacing the LED Control Board Replacing Pre-Installed Components LAN/ID Replacing the M1012 Adapter BoardFan Cables J3 LAN/ID LED 1 M1012 Adapter Board Features for B3970-U2 M1012 Adapter Board Connector Pin Definition FAN Signal Related Connector Pin Definition GND FAN1TACH FAN2TACH FAN3TACH KEY PIN FAN312VPWM FAN3TACH GND FAN4TACH FAN412VPWM FAN912VPWM FAN9TACH GND FAN10TACH Replacing the Sata Backplane Replacing Pre-Installed Components 1 SAS/SATA Backplane M1208 Features J4, SAS/SATA Replacing the Power Supply Replacing Pre-Installed Components B3970-U Advanced/Hardware Health Configuration Appendix I Bios DifferencesBios Setup Utility Advanced S3970 Advanced/Hardware Health ConfigurationSystem Fan to M1012 Adapter Board Sata CableFAN Cable B3970-UG20S4H ModelPower Supply to M1208 Sata Backplane Power Supply CablePower Supply to Motherboard Power Supply to M1012 Adapter BoardFDD Related Cable Option Other CablesM1003 Front Panel Control Board Related Cable CD-ROM Related CableAppendix III Installing Smdc Cards Installing M3289 into HDD Tray Page Installing M3290/M3291 into HDD tray Page Installing M3290/M3291 into GT24 Chassis Page Page Help Resources Technical SupportReturning Merchandise for Service