G7/F7/L7/E7 inverter PLC 367 | Omron G7, F7, L7, E7 specs

Item		Specifications
		3G3RV-P10ST8-E	3G3RV-P10ST8-DRT-E
Link bits (LR area)		256 bits: LR 0000 to LR 1515 (words LR 00 to LR 15)

Timers/counters		256 timers/counters (TIM/CNT 000 to TIM/CNT)
		1-ms timers: TMHH(--)
		10-ms timers: TIMH(15)
		100-ms timers: TIM
		1-s/10-s timers: TIML(--)
		Decrementing counters: CNT
		Reversible counters: CNTR(12)
CompoBus/S master functions		Remote I/O devices can be allocated up to 256 I/O points (128 inputs and 128 outputs) in input area IR 020 to
		IR 027 and output area IR 030 to IR 037.
		• The node numbers can be set to 0 to 7 (128-point mode) or 0 to 15 (256-point mode).
		• The communications mode can be set to high-speed mode (max. length 100 m) or long-distance mode
		(max. length 500 m).

DeviceNet slave functions		Up to 64 words (32 input words and 32 output words) can be allocated to the DeviceNet master's I/O.
		The master's I/O can be allocated to the following data areas:
		IR 000 to IR 049
		IR 200 to IR 227
		DM 0000 to DM 2047
		LR 00 to LR 15
		HR 00 to HR 19
		AR 00 to AR 23 (3G3RV-P10ST ' master; read-only)
		TC 000 to TC 255
		• Explicit message communications are supported. Any 3G3RV-P10ST data area can be accessed from the
		DeviceNet master.
		• The communications speed can be set to 500 kbps (total network length 100 m max.), 250 kbps (total network
		length 250 m max.), or 125 kbps (total network length 500 m max.).
DM area	Read/write	2,029 words (DM 0000 to DM 0999, DM 1019 to DM 2047)
		DM 2000 to DM 2021: error log storage area

	Read only	456 words (DM6144 to 6599)
	Inverter interface	19 words (DM 2022 to DM 2040)
	Encoder interface	14 words (DM 1986 to DM 1999)

	PLC setup	56 words (DM 6599 to DM 6655)
Interrupts		Interrupt inputs
		2 inputs
		Response time: 50 µs
		Interval timer interrupts	Scheduled interrupts
		1 input
		Set value: 0.5 to 319,968 ms	One-shot interrupt
		Precision: 0.1 ms

High-speed counters	High-speed counter 1 input,	No interrupt
	see note 5
	Differential phase mode (5 kHz)	Count-check interrupt
	Pulse plus direction input mode	(An interrupt can be generated when the count equals the set value or the count lies within a preset range.)
	(20 kHz)
	Up/down input mode (20 kHz)
	Increment mode (20 kHz)
	Interrupt inputs (counter mode)	No interrupt
	2 inputs	Count-up interrupt
	Incrementing counter (2 kHz)
	Decrementing counter (2 kHz)
Encoder interface		3 input modes:
		Differential-phase (up/down)
		Pulse plus direction
		Up/down pulse
		Maximum input frequency 50 kHz
		Maximum counter range 4,294,967,295 (232-1)
		Two capture registers, 3 selectable registration inputs
		One comparison value
		Counter reset through software or Z-phase
		Interrupt function

Pulse outputs		• 2 outputs:
		Single-phase pulse output without acceleration/deceleration (see note 6.)
		10 Hz to 10 kHz
		• 2 outputs:
		Variable duty ratio pulse output (see note 6.)
		0.1 to 999.9 Hz, duty ratio 0 to 100%
		• 1 output:
		Pulse output with trapezoidal acceleration/deceleration (see note 6.)
		Pulse plus direction output, up/down pulse output, 10 Hz to 10 kHz

Synchronized pulse control		1 point, see notes 5 and 6
		Input frequency range: 10 to 500 Hz, 20 Hz to 1 kHz, or 300 Hz to 20 kHz
		Output frequency range: 10 Hz to 10 kHz

Pulse catch inputs		2 bits
		Minimum pulse input: 50 µs max.
		Used in common by input interrupts and input interrupt counter mode.

Analog volume		None
Input time constant		Determines the input time constant for all inputs. (settings: 1, 2, 3, 5, 10, 20, 40, or 80 ms)
(ON response time = OFF response time)

Clock/Calendar function		Shows the current year, month, day of the week, day of the month, hour, minute, and second.
Communication function		Port 1 = Peripheral and RS-422:
		Host link, peripheral bus, no-protocol, programming console
		Port 2 = RS-232C port:
		Host link, no-protocol, 1:1 PLC link, 1:1 NT link

3G3RV-P10ST8-DRT-E

G7/F7/L7/E7 inverter PLC

367