Omron DR 170 14 manual Klinkmann Automation Omron Ethernet DAServer

Page 64

Klinkmann Automation Omron Ethernet DAServer

62

04

Node number setting error.

operation manual)

Make sure the node number is within specified range and that there are no duplicate node numbers.

DASProtFail

04: Not

01

executable

 

 

 

05:Routing 01 error

02

03

04

10:01

Command format error

02

03

05

11:00

Parameter error

An undefined command has been used, or short frame (4 bytes) is being used for FINS header frame.

Destination node number is not set in the routing tables.

Routing tables aren't registered.

Routing table error.

The maximum number of relay nodes (2) was exceeded in the command.

The command is longer than the max. permissible length.

The command is shorter than the min. permissible length.

The designated number of data items differs from the actual number.

An incorrect header has been used. (Data for another node was received. Attempt was made to send response to broadcast address)

The parameter in the command data were incorrect or the

Check the command code and be sure code is supported by Unit to which command is sent.(*)

Set the remote PLC in the routing tables.

Set the the routing tables at the relay nodes and remote node.

Set the the routing tables correctly.

Redesign the network to reduce number of relay nodes.

Check the command format and set it correctly.(*)

Check the command format and set it correctly.(*)

Check the number of items and data and make sure that they agree.(*)

Check the header parameters in the command and be sure the correct command format is used.(*)

Check the parameters and be sure the socket number is between 1

DASProtFail

DASProtFail

DASProtFail

DASProtFail

DASProtFail

DASProtFail

DASProtFail

DASProtFail

DASProtFail

DASProtFail

Omron Ethernet DAServer Ver 1.x User Manual Rev 1.4

17014m14

Image 64
Contents Omron Ethernet Direct DAServer User’s Guide Ver 1.x Rev DR 170Contents About This User Guide ContentsIndex Introduction OverviewApplication Communications Protocols Communication ProtocolsSuiteLink Accessing Items via the DAServer Fins Message CommunicationFastDDE NetDDEDDE/SuiteLink Features Demo ModeKlinkmann Automation Omron Ethernet DAServer Before starting the Omron Ethernet DAServer Ethernet Unit Configuration Example for CS1 PLC Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Comments on example program ladder diagram Example program for sending unsolicited data from PLCKlinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Getting Started Quickly with the DAServer To prepare the Omron Ethernet DAServerNewSOCKET000 by default Configuring the DAServerAdd Controller Object To prepare the Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer To create Socket objects from the Configuration branch DASOmronEth Hierarchy in the DAServer ManagerPort Number Host Name IP AddrTo add Controller to your Omron Ethernet hierarchy Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Enabling Software License Key for DASOmronEth Configuring Device Group Definitions Device Group DefinitionsTo create or add device groups To make edits on device groupsKlinkmann Automation Omron Ethernet DAServer To delete device groups To configure default update intervalsScan-Based Message Handling Configuring Device Item Definitions Archiving Configuration SetsTo archive configuration sets To use different configuration sets from the current oneDevice Item Definitions Name Item ReferenceTo create or add device items To add item referencesHot Configuration Klinkmann Automation Omron Ethernet DAServer Item Name General Format PnSPnb or Pnbb or Pn.b or Pn.bb Pn-PhSBCD Format Long Format Signed/BCDFloating Point Format IEEE/BCD Ascii Strings FormatWrite ReadImortant Note = a To M CS1/CJ1 PLCs= a Klinkmann Automation Omron Ethernet DAServer C200HX/C200HG/C200HE PLCs CV-series PLCs PVS Flag or Bit Status Step StatusCPM2x PLCs Klinkmann Automation Omron Ethernet DAServer CQM1 PLCs DAServer Standard System Items System Item Type Description Values Name Access Rights DAServer Global System ItemDAServer Device-Specific System Items System Item Type Description ValuesKlinkmann Automation Omron Ethernet DAServer DAServer Device-Group-Specific System Items RangeRange Generic OPC Syntax AREA10.VESSEL1.TIC1.PLC.D100Monitoring Connectivity Status with the PLC YourOPCAccessPath.$SYS$Status=DASOmronEthPLC!$SYS$Status Monitoring the Status of DAS Conversations Using DDEStatus and IOStatus in ExcelReading Values from the DAServer into Excel Writing Values to the DAServer from Excel Channel=INITIATEapplicationname,topicname=POKEchannel,itemname, DataReference =TERMINATEchannelDAServer Error Messages Error Messages and CodesError Message Explanation Probable Cause Solution Log Flag Item Names Creating write Invalid value poked Check Item’s DASProtFail Data, received Take into DASProtWarn Server-Specific Error Codes Error code Logger Message Log FlagFins Response Codes Main Code Sub Probable Cause Remedy Log Flag HexKlinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer DAServer Architecture DAServersDAS Engine Plug-insPLC Protocol Layer Component Environments Klinkmann Automation
Related manuals
Manual 67 pages 16.17 Kb

DR 170 14 specifications

The Omron DR 170 14 is a leading-edge digital infrared thermometer that has established a strong reputation for its accuracy and efficiency in measuring body temperature. This advanced device is particularly noted for its user-friendly design, making it suitable for both medical professionals and home use.

One of the key features of the Omron DR 170 14 is its non-contact measurement capability, allowing users to obtain temperature readings from a distance of about 1-3 centimeters. This feature is crucial in minimizing the risk of cross-contamination, especially in healthcare settings. The thermometer utilizes infrared technology to detect the infrared energy emitted by the body, ensuring quick and reliable readings in just seconds.

The Omron DR 170 14 also boasts a large, easy-to-read LCD display that provides clear visibility of temperature readings. This display is backlit, allowing for usage in low-light conditions, making it convenient during nighttime monitoring of children's temperatures.

Furthermore, the device includes a memory function that can store multiple temperature readings, assisting users in tracking fever patterns over time. This feature is invaluable for caregivers and healthcare providers as it allows for better assessment and decision-making regarding treatment plans.

In terms of accuracy, the Omron DR 170 14 is equipped with advanced measurement algorithms that enhance precision in readings, positioning it as a reliable option for temperature measurement. The thermometer can measure not only body temperature but also surface temperatures of objects and liquids, providing versatility beyond just clinical settings.

Another notable characteristic is its compact and lightweight design, which makes it highly portable and easy to carry around, whether in a medical bag or a home setting. The thermometer is also powered by batteries, ensuring that it remains operational even in case of power outages.

Overall, the Omron DR 170 14 stands out for its combination of modern technology, ease of use, and reliable performance. With its non-contact functionality, rapid readings, and memory features, it serves as an essential tool for anyone needing accurate temperature assessments, whether in a clinical or home environment. The thermometer exemplifies Omron's commitment to creating healthcare solutions that are not only innovative but also accessible to a wide range of users.