Omron DR 170 14 manual Klinkmann Automation Omron Ethernet DAServer

Page 63

Klinkmann Automation Omron Ethernet DAServer

61

03

05

number too large.

Send error caused by lack of available space in PLC internal buffers.

Node number setting error.

number below the maximum node number.

Reduce the traffic on the

DASProtFail

Ethernet Unit. Check

 

user application.

 

 

 

Make sure the node

DASProtFail

number is within

 

specified range and that

 

there are no duplicate

 

node numbers.

 

 

 

06

Node number duplication error.

Make sure that there are DASProtFail no duplicate node

numbers.

02:Remote 01 node error

IP address of remote node was not set correctly in IP address table or IP router table.

Set IP address of remote node into IP address table, and, if internetwork transmission is required, into IP router table.

DASProtFail

02

No node with the

Check the remote

DASProtFail

specified unit address.

node’s unit address and

 

 

make sure the correct

 

 

one is being used in the

 

 

control data.

 

 

 

 

05

03:01

Communic. Controller error

02

Message packet was corrupted by transmission error or response time-out (response watchdog timer interval too short) or transmission frame corrupted or PLC internal reception buffer full.

Error occured in the communications controler. ERC indicator is lit.

CPU error occured in the PC at the destination node.

Check the protocol and controller status by reading them with FINS commands. Increase the number of transmit retry attempts.

Increase the value for the response monitor time in the control data. Read out the error log and correct as required.

Take corrective action, referring to troubleshooting procedures in PLC manual.

Check the CPU indicators at remote PLC and clear the error in the CPU (refer to the PLC’s

DASProtFail

DASProtFail

DASProtFail

Omron Ethernet DAServer Ver 1.x User Manual Rev 1.4

17014m14

Image 63
Contents Ver 1.x Rev DR 170 Omron Ethernet Direct DAServer User’s GuideContents Contents About This User GuideIndex Overview IntroductionCommunication Protocols Application Communications ProtocolsSuiteLink NetDDE Accessing Items via the DAServerFins Message Communication FastDDEDDE/SuiteLink Demo Mode FeaturesKlinkmann Automation Omron Ethernet DAServer Before starting the Omron Ethernet DAServer Ethernet Unit Configuration Example for CS1 PLC Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Example program for sending unsolicited data from PLC Comments on example program ladder diagramKlinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer To prepare the Omron Ethernet DAServer Getting Started Quickly with the DAServerConfiguring the DAServer NewSOCKET000 by defaultAdd Controller Object To prepare the Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer DASOmronEth Hierarchy in the DAServer Manager To create Socket objects from the Configuration branchHost Name IP Addr Port NumberTo add Controller to your Omron Ethernet hierarchy Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Enabling Software License Key for DASOmronEth Device Group Definitions Configuring Device Group DefinitionsTo make edits on device groups To create or add device groupsKlinkmann Automation Omron Ethernet DAServer To configure default update intervals To delete device groupsScan-Based Message Handling To use different configuration sets from the current one Configuring Device Item DefinitionsArchiving Configuration Sets To archive configuration setsTo add item references Device Item DefinitionsName Item Reference To create or add device itemsHot Configuration Klinkmann Automation Omron Ethernet DAServer Pn-PhS Item Name General FormatPnS Pnb or Pnbb or Pn.b or Pn.bbAscii Strings Format BCD FormatLong Format Signed/BCD Floating Point Format IEEE/BCDRead WriteImortant Note CS1/CJ1 PLCs = a To M= a Klinkmann Automation Omron Ethernet DAServer C200HX/C200HG/C200HE PLCs CV-series PLCs PVS Step Status Flag or Bit StatusCPM2x PLCs Klinkmann Automation Omron Ethernet DAServer CQM1 PLCs DAServer Standard System Items System Item Type Description Values System Item Type Description Values Name Access RightsDAServer Global System Item DAServer Device-Specific System ItemsKlinkmann Automation Omron Ethernet DAServer Range DAServer Device-Group-Specific System ItemsRange AREA10.VESSEL1.TIC1.PLC.D100 Generic OPC SyntaxYourOPCAccessPath.$SYS$Status Monitoring Connectivity Status with the PLC=DASOmronEthPLC!$SYS$Status Using DDEStatus and IOStatus in Excel Monitoring the Status of DAS ConversationsReading Values from the DAServer into Excel =TERMINATEchannel Writing Values to the DAServer from ExcelChannel=INITIATEapplicationname,topicname =POKEchannel,itemname, DataReferenceError Messages and Codes DAServer Error MessagesError Message Explanation Probable Cause Solution Log Flag Item Names Creating write Invalid value poked Check Item’s DASProtFail Data, received Take into DASProtWarn Main Code Sub Probable Cause Remedy Log Flag Hex Server-Specific Error CodesError code Logger Message Log Flag Fins Response CodesKlinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer Klinkmann Automation Omron Ethernet DAServer DAServers DAServer ArchitecturePlug-ins DAS EnginePLC Protocol Layer Component Environments Klinkmann Automation
Related manuals
Manual 67 pages 16.17 Kb

DR 170 14 specifications

The Omron DR 170 14 is a leading-edge digital infrared thermometer that has established a strong reputation for its accuracy and efficiency in measuring body temperature. This advanced device is particularly noted for its user-friendly design, making it suitable for both medical professionals and home use.

One of the key features of the Omron DR 170 14 is its non-contact measurement capability, allowing users to obtain temperature readings from a distance of about 1-3 centimeters. This feature is crucial in minimizing the risk of cross-contamination, especially in healthcare settings. The thermometer utilizes infrared technology to detect the infrared energy emitted by the body, ensuring quick and reliable readings in just seconds.

The Omron DR 170 14 also boasts a large, easy-to-read LCD display that provides clear visibility of temperature readings. This display is backlit, allowing for usage in low-light conditions, making it convenient during nighttime monitoring of children's temperatures.

Furthermore, the device includes a memory function that can store multiple temperature readings, assisting users in tracking fever patterns over time. This feature is invaluable for caregivers and healthcare providers as it allows for better assessment and decision-making regarding treatment plans.

In terms of accuracy, the Omron DR 170 14 is equipped with advanced measurement algorithms that enhance precision in readings, positioning it as a reliable option for temperature measurement. The thermometer can measure not only body temperature but also surface temperatures of objects and liquids, providing versatility beyond just clinical settings.

Another notable characteristic is its compact and lightweight design, which makes it highly portable and easy to carry around, whether in a medical bag or a home setting. The thermometer is also powered by batteries, ensuring that it remains operational even in case of power outages.

Overall, the Omron DR 170 14 stands out for its combination of modern technology, ease of use, and reliable performance. With its non-contact functionality, rapid readings, and memory features, it serves as an essential tool for anyone needing accurate temperature assessments, whether in a clinical or home environment. The thermometer exemplifies Omron's commitment to creating healthcare solutions that are not only innovative but also accessible to a wide range of users.